OptiStruct

Discussion List

• 
  Solar panel deflection due to wind!

  GTT Johan 31 views 0 comments 0 points Most recent by GTT Johan September 24Altair HyperWorks
• 
  Thermal topology optimization with mechanical constraint

  Question Benjamin_20249 294 views 1 comment 0 points Most recent by Adriano_Koga September 20Community Q&A
• 
  Create a function driven response Optistruct

  Answered ✓ TomSouthall 155 views 1 comment 0 points Most recent by Adriano_Koga September 20Community Q&A
• 
  simulation

  Question Alberto Buccellato 84 views 1 comment 0 points Most recent by Adriano_Koga September 20Community Q&A
• 
  Apply symmetry restrictions over design space or not

  Question MaUb 93 views 1 comment 0 points Most recent by Adriano_Koga September 20Community Q&A
• 
  Comparison Between Component Mode Synthesis Methods

  Christopher_Fadanelli 72 views 0 comments 1 point Most recent by Christopher_Fadanelli September 13Altair HyperWorks
• 
  How can I get Factor fo Safety into linear static analysis in SIMLAB

  Question Ludovico Zanellati 129 views 1 comment 0 points Most recent by Ioannis_Makris September 13Community Q&A
• 
  Exclude single ply from composite optimization

  Answered JBrai_21295 113 views 2 comments 0 points Most recent by Adriano_Koga September 12Community Q&A
• 
  Problem with RBE3 in Hyperworks

  Answered Guilherme Arruda 1.4K views 4 comments 0 points Most recent by Guilherme Arruda September 12Community Q&A
• 
  Why does my part moves against gravity in Nonlinear transient once it contacts rigid mesh

  Answered Natalia Reynoso 92 views 2 comments 0 points Most recent by Rajashri_Saha September 11Community Q&A
• 
  Effect of de value of modal contact stiffness of preload on modal frequency.

  Question Weidong Li 112 views 1 comment 0 points Most recent by Adriano_Koga September 11Community Q&A
• 
  How to decide optimisation objectives and element density threshold

  Answered ✓ TomSouthall 155 views 5 comments 0 points Most recent by TomSouthall September 11Community Q&A
• 
  Beginner with Optistruct: Questions about "big models"

  Answered Florian GENTY 336 views 2 comments 0 points Most recent by Florian GENTY September 10Community Q&A
• 
  Combined dynamic load

  Answered Alberto Buccellato 132 views 3 comments 0 points Most recent by Rajashri_Saha September 10Community Q&A
• 
  Avoid objects in design area for topology optimisation

  Answered ✓ TomSouthall 147 views 8 comments 0 points Most recent by Rajashri_Saha September 6Community Q&A
• 
  ERROR # 312 *** In static load case 1 the compliance is negative or large 1.52002e+09. Optimization/buckling analysis cannot be performed. due to possible rigid body model.

  Answered Moawez Zamir Awan 2K views 6 comments 0 points Most recent by Rajashri_Saha September 6Community Q&A
• 
  Multiple load collectors into one load step

  Answered ✓ TomSouthall 217 views 4 comments 0 points Most recent by loistf September 5Community Q&A
• 
  Time Dependent analysis

  Answered Parthiban B 175 views 5 comments 0 points Most recent by loistf September 5Community Q&A
• 
  Optistruct solution sticking to design boundary

  Answered ✓ TomSouthall 158 views 3 comments 0 points Most recent by TomSouthall September 4Community Q&A
• 
  Output for Param, inrel

  Answered Nicolas_20776 152 views 3 comments 0 points Most recent by Rajashri_Saha September 4Community Q&A
• 
  How do you keep simulations running off-hours?

  Question David Hubin 190 views 1 comment 0 points Most recent by Rajashri_Saha September 4Community Q&A
• 
  How to input damping coefficient on Param Card (G)?

  Question Andres Salinas 171 views 1 comment 0 points Most recent by Rajashri_Saha September 4Community Q&A
• 
  Print out Response values without an optimization

  Question Nicolas_20776 129 views 1 comment 0 points Most recent by loistf September 2Community Q&A
• 
  Composite stress contour plot image quality

  Answered Hypermesh 2023.1_Optistruct 226 views 6 comments 0 points Most recent by loistf September 2Community Q&A
• 
  Is it possible to create transient response analysis for fluid domains?

  Answered Dennis_20682 143 views 2 comments 0 points Most recent by Xiaolei September 2Community Q&A
• 
  MultiScale Designer 材料を使って、OptiStruct 非線形解析で引張と圧縮のヤング率を変える方法

  altair_fukuoka 23 views 0 comments 1 point Most recent by altair_fukuoka August 30Altair HyperWorks - 日本語
• 
  Super Element Generator Script

  Will Asproth 245 views 0 comments 0 points Most recent by Will Asproth August 29Altair Exchange
• 
  【チュートリアル】HyperMesh / OptiStructを使用した過渡応答解析

  Harada_21719 118 views 0 comments 0 points Most recent by Harada_21719 August 29Altair HyperWorks - 日本語
• 
  【チュートリアル】HyperMesh / OptiStructを使用した固有値解析

  Harada_21719 276 views 0 comments 0 points Most recent by Harada_21719 August 28Altair HyperWorks - 日本語
• 
  Bulk data example for flexible body creation (CMS)

  Giorgio 99 views 0 comments 0 points Most recent by Giorgio August 28Altair Exchange