Discussion List

• 
  How to correctly simulate a heat sink that was additive manufactured??

  Answered Angel_gonzalez 123 views 3 comments 0 points Most recent by acupro September 2024Community Q&A
• 
  FPSO Roll motion

  Answered AdamK 145 views 3 comments 0 points Most recent by acupro September 2024Community Q&A
• 
  Wall function

  Answered K. Yamamoto 148 views 1 comment 0 points Most recent by acupro September 2024Community Q&A
• 
  AcuSolve 2023を使い始めるにあたって (HyperWorks CFD 2023 対応)

  Masu 319 views 0 comments 0 points Most recent by Masu September 2024Altair HyperWorks - 日本語
• 
  How to fix Error from fLesGetHbrgEig <40> in acusolve (acusolve failed to launch after certain iteration)

  Answered Mudassir khan 1.3K views 3 comments 1 point Most recent by acupro September 2024Community Q&A
• 
  Mesh quality

  Answered K. Yamamoto 165 views 1 comment 0 points Most recent by acupro September 2024Community Q&A
• 
  Importing mesh from hyperworks to hyperworks CFD

  Answered Ashish Raman_20688 131 views 1 comment 0 points Most recent by ydigit September 2024Community Q&A
• 
  Acusolve student version setup

  Answered Jahnavi Gupta 154 views 1 comment 0 points Most recent by acupro August 2024Community Q&A
• 
  How to set outflow_type of AcuSolve

  Answered K. Yamamoto 125 views 1 comment 0 points Most recent by acupro August 2024Community Q&A
• 
  AcuSolve 2024を使い始めるにあたって(HyperWorks CFD 2024 対応)

  Masu 219 views 0 comments 0 points Most recent by Masu August 2024Altair HyperWorks - 日本語
• 
  Restart a acusolve calculation on supercomputer

  Answered K. Yamamoto 129 views 1 comment 0 points Most recent by acupro August 2024Community Q&A
• 
  A segmentation error

  Answered K. Yamamoto 178 views 3 comments 0 points Most recent by acupro August 2024Community Q&A
• 
  Roughness height in wall function

  Answered K. Yamamoto 134 views 1 comment 0 points Most recent by acupro August 2024Community Q&A
• 
  Governing equation of acutrace

  Answered K. Yamamoto 215 views 2 comments 0 points Most recent by K. Yamamoto August 2024Community Q&A
• 
  AcuSolve 2022を使い始めるにあたって(HyperWorks CFD 2022.2 対応)

  Masu 28 views 0 comments 0 points Most recent by Masu August 2024Altair HyperWorks - 日本語
• 
  Permeability in porous media

  Answered Prabin Pradhananga_22497 101 views 1 comment 0 points Most recent by acupro August 2024Community Q&A
• 
  Stop AcuSolve job in Altair Access web

  Answered Sebastian Yang 408 views 4 comments 0 points Most recent by Adarsh August 2024Community Q&A
• 
  Steady-state stokes flow simulation

  Answered Prabin Pradhananga_22497 171 views 3 comments 0 points Most recent by acupro August 2024Community Q&A
• 
  How I can find out the center of pressure??

  Answered Javier Mediavilla Hidalgo 259 views 4 comments 0 points Most recent by ydigit August 2024Community Q&A
• 
  On mesh_motion of cross section in fluid structure interaction (DC-FSI) with Acusolve and Optistruct

  Accepted ✓ Motoki_Koga 223 views 4 comments 0 points Most recent by Motoki_Koga July 2024質問と回答 (Q&A)
• 
  What is the specified pressure of a simple boundary condition with a constant-flow inlet velocity?

  Answered Peter Parrish_22382 153 views 6 comments 0 points Most recent by acupro July 2024Community Q&A
• 
  Pyrolysis gases: Gas models for Acusolve CFD

  Answered iceman0723 179 views 1 comment 0 points Most recent by acupro July 2024Community Q&A
• 
  Radiation : ERROR: Inner/Outer surface_sets in shell surface not found

  Answered Atmos 161 views 1 comment 0 points Most recent by ydigit July 2024Community Q&A
• 
  Moving Body Capabilities

  Answered Nazrin 211 views 4 comments 0 points Most recent by acupro July 2024Community Q&A
• 
  Does Large Eddy simulation Use a Wall Function?

  Answered Peter Parrish_22382 157 views 1 comment 0 points Most recent by acupro July 2024Community Q&A
• 
  Introduction to CFD-DEM for modelling fluid-particle systems

  jerrinjobs 502 views 0 comments 0 points Most recent by jerrinjobs July 2024Altair HyperWorks
• 
  AcuSolveの単位

  Masu 117 views 0 comments 0 points Most recent by Masu July 2024Altair HyperWorks - 日本語
• 
  Is it possible to monitor the energy balance at each time step during a transient conjugate heat transfer simulation?

  Answered Jagan 95 views 1 comment 0 points Most recent by acupro July 2024Community Q&A
• 
  AcuOut installation

  Accepted ✓ Peter Parrish_22382 205 views 4 comments 0 points Most recent by Peter Parrish_22382 June 2024Community Q&A
• 
  hypermesh2023. May I ask what error this is? How to modify it？

  Answered bigshow 180 views 6 comments 0 points Most recent by ydigit June 2024Community Q&A