OptiStruct

Discussion List

• 
  FSI on thin part

  Answered Junta_20361 177 views 4 comments 0 points Most recent by Junta_20361 April 2021Community Q&A
• 
  Unable to Mesh and Solve

  Accepted ✓ Sujay Pattiwar 388 views 6 comments 0 points Most recent by Viraj_Kulkarni April 2021Community Q&A
• 
  optistruct 2020 - Where can I find PERBC and RELOC

  Answered Sitou_21548 539 views 2 comments 0 points Most recent by Gildas_GUILLY April 2021Community Q&A
• 
  unselectable Node-Sets in Hypermesh 2020.1.1 with OS (only SET_GRID is selectable)

  Answered Klaus_21165 562 views 3 comments 0 points Most recent by Klaus_21165 April 2021Community Q&A
• 
  Can one do Design Sensitivity Analysis on Normal Modes

  Answered Numair 250 views 1 comment 0 points Most recent by RobHoglund April 2021Community Q&A
• 
  Virtual conference - ATCx Heavy Equipment

  Corinne_Bossy 507 views 0 comments 0 points Most recent by Corinne_Bossy April 2021Altair HyperWorks
• 
  Mfluid in Modal frequency response simulation

  Answered Rex_22369 336 views 2 comments 0 points Most recent by Rex_22369 April 2021Community Q&A
• 
  Error 1026

  Answered Anıl Türkseven 789 views 1 comment 0 points Most recent by Adriano Koga_20259 April 2021Community Q&A
• 
  Error 14

  Answered Anıl Türkseven 363 views 2 comments 0 points Most recent by Jason_Craanen April 2021Community Q&A
• 
  Whether the local CID rotates with the CBush element

  Answered Mariusz Figarski 279 views 2 comments 0 points Most recent by paulel_22250 April 2021Community Q&A
• 
  errors while solving in hypermesh desktop 2020

  Answered Lekha Bhatt 490 views 1 comment 0 points Most recent by Adriano Koga_20259 April 2021Community Q&A
• 
  MFLUID as MODAL BASE for a MODAL FREQUENCY RESPONSE

  Answered Altair Forum User 1.5K views 2 comments 0 points Most recent by Rex_22369 April 2021Community Q&A
• 
  Random vibration analysis unit conversion in optistruct

  Answered mh_20798 926 views 2 comments 0 points Most recent by Lacie April 2021Community Q&A
• 
  Do I have to create a beam cross section after using PBEAML card image?

  Answered MOHAMMAD UMAR MAKNOJIYA 761 views 1 comment 0 points Most recent by Adriano Koga_20259 April 2021Community Q&A
• 
  what is the meaning of penalty factor in Topology Optimization?

  Answered Sreekanth 1.6K views 1 comment 0 points Most recent by Adriano Koga_20259 April 2021Community Q&A
• 
  Problems running FSI heat transfer analysis with OptiStruct

  Answered Apostolos Lazios 230 views 3 comments 0 points Most recent by Apostolos Lazios April 2021Community Q&A
• 
  How to resolve error # 5408 while performing Modal Frequency Response Analysis?

  Answered Anees Sunesra 1.5K views 2 comments 0 points Most recent by Adriano Koga_20259 April 2021Community Q&A
• 
  Modelling of stator or rotor laminates or equivalent modeling for motor structural analysis?

  Answered Mintu 597 views 4 comments 0 points Most recent by Zhou XU April 2021Community Q&A
• 
  How to apply 1.5 MN load by using MPC in a large train sidewall?

  Answered David_21519 200 views 1 comment 0 points Most recent by QuyNguyenDai April 2021Community Q&A
• 
  MUMPS memory error - Optistruct

  Answered inasiopo 10K views 11 comments 0 points Most recent by inasiopo April 2021Community Q&A
• 
  Ratio between contact stabilization energy and the strain energy

  Answered MarioS 1.8K views 1 comment 1 point Most recent by RobHoglund March 2021Community Q&A
• 
  Controlling OptiStruct Output Frequency with the NLOUT Card

  paulel_22250 186 views 0 comments 1 point Most recent by paulel_22250 March 2021Altair HyperWorks
• 
  Analysis setting for running large models

  Answered AmirMar 494 views 2 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Can create multiple objectives in optimization

  Answered Anjaney 969 views 2 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  How to run Optistruct jobs on Ubuntu terminal

  Answered alpha_21885 3.4K views 10 comments 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  How to transfer the load applied on one component to another connected component?

  Answered MOHAMMAD UMAR MAKNOJIYA 294 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  how represent correctly a certain given PSD

  Answered Francesco Porcari 145 views 1 comment 0 points Most recent by Thomas Quenaon_21507 March 2021Community Q&A
• 
  How to setup topology analysis to meet response frequency requirement

  Answered Daf 153 views 3 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  Displacement response specific to subcase

  Answered Max Sandberg Samset_21334 1.1K views 1 comment 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  How to eliminate the error #721

  Answered MOHAMMAD UMAR MAKNOJIYA 1.4K views 1 comment 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A