OptiStruct

Discussion List

• 
  Compose & OptiStruct Synergy: OML & DRESP3

  Roberta Varela_20843 160 views 0 comments 2 points Most recent by Roberta Varela_20843 March 2021Altair HyperWorks
• 
  I did a simple 1D beam model with a load applied, and the results didn't show me the stress values, although the displacement values were shown. The output request is in the H3D format for both outputs, and the Pbeam properties have the moments of i

  Answered Afonso Rainha 89 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Acoustic Analysis

  Answered anmolk 2.1K views 6 comments 0 points Most recent by anmolk March 2021Community Q&A
• 
  Response to impulse cantilever beam

  Answered Francesco Porcari 407 views 1 comment 0 points Most recent by Kory March 2021Community Q&A
• 
  Which PARAM should I use to put this model to run in a Optistruct?

  Answered Melzak Silva 411 views 1 comment 0 points Most recent by RobHoglund March 2021Community Q&A
• 
  Apply Enforced Displacment

  Answered Altair Forum User 6.1K views 17 comments 0 points Most recent by Altair Forum User March 2021Community Q&A
• 
  Rigid Body(PRBODY) in Optistruct

  Answered Subash Karthikeyan 1.6K views 7 comments 0 points Most recent by Ingeniorator March 2021Community Q&A
• 
  RAMの容量について

  Answered Saya 344 views 1 comment 0 points Most recent by AltairTY March 2021Community Q&A
• 
  Optistructのジョブ完了時に完了メールを送信したい

  Answered Yuichiro Aoki 220 views 1 comment 0 points Most recent by AltairTY March 2021質問と回答 (Q&A)
• 
  Additive Manufacturing with Draw Constraint

  Answered Baturalp OGUZ_20261 176 views 1 comment 0 points Most recent by RobHoglund March 2021Community Q&A
• 
  GPU solving set up

  Answered Carlos Garza_20271 264 views 2 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  All types of edges in model are appearing in blue color

  Accepted ✓ AshwaniMittal 1.4K views 4 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  Moment describing

  Answered Anıl Türkseven 216 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Export multiple forces (in different directions) from Flux.

  Answered Boris_22428 218 views 1 comment 0 points Most recent by asoualmi February 2021Community Q&A
• 
  OptistructでGeom non-linear(expl dynamic)を実行すると、PENTA6がコメントアウトされて変換されなかったり、問題なく変換されたりするは何が原因でしょうか？

  Answered Takushi Kawaoka 192 views 1 comment 0 points Most recent by fujita February 2021Community Q&A
• 
  Tyre Assembly Analysis

  Answered Altair Forum User 1.6K views 8 comments 0 points Most recent by Altair Forum User February 2021Community Q&A
• 
  *** ERROR # 1728 *** in the input data: Incorrect SET definition

  Answered Altair Forum User 4.5K views 3 comments 0 points Most recent by Kiran Govind February 2021Community Q&A
• 
  Coupling parametric CAD body with meshing and analysis setup in HyperMesh?

  Answered Ingeniorator 275 views 4 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  No change in mass after size optimization

  Answered Joao_21860 158 views 2 comments 0 points Most recent by Joao_21860 February 2021Community Q&A
• 
  Getting 0 stress from a 1D model beam

  Answered Achmad Zufar 760 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  How do we get the fibre orientation tensor in OptiStruct during composite analysis ?

  Answered sagar hiremath 230 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Non linear 2D orthotropic

  Answered Alessio Piccolo 243 views 2 comments 0 points Most recent by Alessio Piccolo February 2021Community Q&A
• 
  Plotting the angle of torsion of a monocoque

  Answered Fabian Wein 920 views 2 comments 0 points Most recent by Fabian Wein February 2021Community Q&A
• 
  Altair Squeak and Rattle Director 2021: Basic Screening Risk Assessment

  Danielle_21252 496 views 0 comments 1 point Most recent by Danielle_21252 February 2021Altair HyperWorks
• 
  Load steps 2 building up on load step 1 nl static

  Answered Benjamin_22203 431 views 1 comment 0 points Most recent by Gildas_GUILLY February 2021Community Q&A
• 
  Volfrac or Massfrac Error in topology optimization

  Accepted ✓ Anıl Türkseven 1.2K views 4 comments 0 points Most recent by Anıl Türkseven February 2021Community Q&A
• 
  Stress constrained Optimization

  Answered Altair Forum User 1.2K views 2 comments 0 points Most recent by Anıl Türkseven February 2021Community Q&A
• 
  OptiStruct ERROR *** ERROR # 6537 *** Inertia relief for nonlinear analysis with non-freeze contact is not allowed.

  Answered Ovunc 1K views 2 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  How to setup Optistruct static analysis output control cards to export results for just a set of elements

  Answered Altair Forum User 3.7K views 5 comments 0 points Most recent by Timothy Er February 2021Community Q&A
• 
  Available courses and webinars

  Answered Praveen Srinivasa_22228 135 views 1 comment 0 points Most recent by Viraj_Kulkarni February 2021Community Q&A