OptiStruct

Discussion List

• 
  Non linear 2D orthotropic

  Answered Alessio Piccolo 231 views 2 comments 0 points Most recent by Alessio Piccolo February 2021Community Q&A
• 
  Plotting the angle of torsion of a monocoque

  Answered Fabian Wein 870 views 2 comments 0 points Most recent by Fabian Wein February 2021Community Q&A
• 
  Altair Squeak and Rattle Director 2021: Basic Screening Risk Assessment

  Danielle_21252 481 views 0 comments 1 point Most recent by Danielle_21252 February 2021Altair HyperWorks
• 
  Load steps 2 building up on load step 1 nl static

  Answered Benjamin_22203 418 views 1 comment 0 points Most recent by Gildas_GUILLY February 2021Community Q&A
• 
  Volfrac or Massfrac Error in topology optimization

  Accepted ✓ Anıl Türkseven 1.1K views 4 comments 0 points Most recent by Anıl Türkseven February 2021Community Q&A
• 
  Stress constrained Optimization

  Answered Altair Forum User 1.2K views 2 comments 0 points Most recent by Anıl Türkseven February 2021Community Q&A
• 
  OptiStruct ERROR *** ERROR # 6537 *** Inertia relief for nonlinear analysis with non-freeze contact is not allowed.

  Answered Ovunc 988 views 2 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  How to setup Optistruct static analysis output control cards to export results for just a set of elements

  Answered Altair Forum User 3.6K views 5 comments 0 points Most recent by Timothy Er February 2021Community Q&A
• 
  Available courses and webinars

  Answered Praveen Srinivasa_22228 129 views 1 comment 0 points Most recent by Viraj_Kulkarni February 2021Community Q&A
• 
  Ah, America’s Cup – getting under the skin!

  Julien Chaussee_20899 3.6K views 1 comment 8 points Most recent by DK123 February 2021Altair HyperWorks
• 
  Multiple DTPL topology optimization

  Answered Baturalp OGUZ_20261 686 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Select many elements by ID

  Accepted ✓ Maximilian Klyk 967 views 3 comments 0 points Most recent by QuyNguyenDai February 2021Community Q&A
• 
  How to apply draw direction constraint?

  Answered Baturalp OGUZ_20261 3K views 4 comments 0 points Most recent by Baturalp OGUZ_20261 February 2021Community Q&A
• 
  Superficial Stresses on 3D Castings? Membrane elements?

  Answered Joel Rodarte 636 views 4 comments 0 points Most recent by Dominic_21343 February 2021Community Q&A
• 
  Converting PCOMPP to PCOMPG/PCOMP

  Answered Max Sandberg Samset_21334 1.1K views 2 comments 0 points Most recent by Max Sandberg Samset_21334 February 2021Community Q&A
• 
  MAC Optimization between two models.

  Answered Numair 295 views 4 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Fatigue life and damage

  Answered Nicolò Lodini_21627 432 views 3 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  How to add Connectivity (Enclosed Voids) Constraint

  Answered Baturalp OGUZ_20261 220 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Modelling Bolt Connection with Contact SLIDE in Optistruct?

  Answered Philipp Link 350 views 8 comments 0 points Most recent by Philipp Link February 2021Community Q&A
• 
  How the fatigue curve are defined?

  Answered Nicolò Lodini_21627 242 views 5 comments 0 points Most recent by Gildas_GUILLY February 2021Community Q&A
• 
  How can I change the referencing coordinate system of different cbeam pin degree of freedom?

  Answered Theo_22364 1.3K views 2 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  changing .fem file error 9

  Answered Paula_21063 385 views 3 comments 0 points Most recent by Paula_21063 February 2021Community Q&A
• 
  MAT9ORT is changing to MAT9 in optimization

  Answered Numair 1.3K views 2 comments 0 points Most recent by Numair February 2021Community Q&A
• 
  Could someone show me an example of section output definition in Opti-struct format?

  Answered Joe Qian 132 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Simultaneous usage of v2017 and v2021 of Hypermesh and Optistruct

  Accepted ✓ Imrich 264 views 1 comment 0 points Most recent by QuyNguyenDai February 2021Community Q&A
• 
  Optistruct Error:1 License Error

  Answered Lukas Kneer_21880 2.2K views 7 comments 0 points Most recent by Joshua Pennington February 2021Community Q&A
• 
  Fatigue Analysis of Composites

  Answered Willi Stork_22391 492 views 4 comments 0 points Most recent by Thomas Quenaon_21507 February 2021Community Q&A
• 
  Error in bolt pretension analysis (nonlinear quasi static analysis)

  Answered Sachin_21833 332 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  Non liner quasi static analysis

  Answered lerik 2.2K views 9 comments 0 points Most recent by FaroukM February 2021Community Q&A
• 
  New features of Hypermesh and Optistruct v2021

  Accepted ✓ Imrich 233 views 1 comment 0 points Most recent by Gildas_GUILLY February 2021Community Q&A