OptiStruct

Discussion List

• 
  Increase in value of History plot of objective function

  Answered Shabbik Shafiulla 242 views 2 comments 0 points Most recent by Shabbik Shafiulla March 2021Community Q&A
• 
  Evaluating damped natural frequencies using Readmac function in Hyperstudy

  Answered Simon Križnik 354 views 4 comments 0 points Most recent by omet March 2021Community Q&A
• 
  Optistruct Optimization : How to setup an optimization on material ID of components?

  Answered Veronique Bouvette 353 views 1 comment 0 points Most recent by Gildas_GUILLY March 2021Community Q&A
• 
  I cannot run Optistruct,

  Answered Bo_21079 145 views 3 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  FEA analysis for the Optimized Design

  Answered Shabbik Shafiulla 385 views 2 comments 0 points Most recent by Shabbik Shafiulla March 2021Community Q&A
• 
  Applying loads/constraints to sets

  Accepted ✓ Fernando Hernández Alonso_20813 747 views 2 comments 0 points Most recent by Fernando Hernández Alonso_20813 March 2021Community Q&A
• 
  how do i get the realistic design model ?

  Accepted ✓ Shabbik Shafiulla 212 views 6 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Element remove/reactivate

  Answered Karthic_22061 721 views 2 comments 0 points Most recent by Minchin John March 2021Community Q&A
• 
  Integrating Altair Compose and other Altair applications

  Roberta Varela_20843 233 views 0 comments 3 points Most recent by Roberta Varela_20843 March 2021Altair HyperWorks
• 
  Compose & OptiStruct Synergy: OML & DRESP3

  Roberta Varela_20843 149 views 0 comments 2 points Most recent by Roberta Varela_20843 March 2021Altair HyperWorks
• 
  I did a simple 1D beam model with a load applied, and the results didn't show me the stress values, although the displacement values were shown. The output request is in the H3D format for both outputs, and the Pbeam properties have the moments of i

  Answered Afonso Rainha 84 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Acoustic Analysis

  Answered anmolk 2.1K views 6 comments 0 points Most recent by anmolk March 2021Community Q&A
• 
  Response to impulse cantilever beam

  Answered Francesco Porcari 392 views 1 comment 0 points Most recent by Kory March 2021Community Q&A
• 
  Which PARAM should I use to put this model to run in a Optistruct?

  Answered Melzak Silva 405 views 1 comment 0 points Most recent by RobHoglund March 2021Community Q&A
• 
  Apply Enforced Displacment

  Answered Altair Forum User 5.7K views 17 comments 0 points Most recent by Altair Forum User March 2021Community Q&A
• 
  Rigid Body(PRBODY) in Optistruct

  Answered Subash Karthikeyan 1.4K views 7 comments 0 points Most recent by Ingeniorator March 2021Community Q&A
• 
  RAMの容量について

  Answered Saya 342 views 1 comment 0 points Most recent by AltairTY March 2021Community Q&A
• 
  Optistructのジョブ完了時に完了メールを送信したい

  Answered Yuichiro Aoki 219 views 1 comment 0 points Most recent by AltairTY March 2021質問と回答 (Q&A)
• 
  Additive Manufacturing with Draw Constraint

  Answered Baturalp OGUZ_20261 163 views 1 comment 0 points Most recent by RobHoglund March 2021Community Q&A
• 
  GPU solving set up

  Answered Carlos Garza_20271 246 views 2 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  All types of edges in model are appearing in blue color

  Accepted ✓ AshwaniMittal 1.3K views 4 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  Moment describing

  Answered Anıl Türkseven 193 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Export multiple forces (in different directions) from Flux.

  Answered Boris_22428 206 views 1 comment 0 points Most recent by asoualmi February 2021Community Q&A
• 
  OptistructでGeom non-linear(expl dynamic)を実行すると、PENTA6がコメントアウトされて変換されなかったり、問題なく変換されたりするは何が原因でしょうか？

  Answered Takushi Kawaoka 191 views 1 comment 0 points Most recent by fujita February 2021Community Q&A
• 
  Tyre Assembly Analysis

  Answered Altair Forum User 1.5K views 8 comments 0 points Most recent by Altair Forum User February 2021Community Q&A
• 
  *** ERROR # 1728 *** in the input data: Incorrect SET definition

  Answered Altair Forum User 4.5K views 3 comments 0 points Most recent by Kiran Govind February 2021Community Q&A
• 
  Coupling parametric CAD body with meshing and analysis setup in HyperMesh?

  Answered Ingeniorator 240 views 4 comments 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  No change in mass after size optimization

  Answered Joao_21860 146 views 2 comments 0 points Most recent by Joao_21860 February 2021Community Q&A
• 
  Getting 0 stress from a 1D model beam

  Answered Achmad Zufar 703 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A
• 
  How do we get the fibre orientation tensor in OptiStruct during composite analysis ?

  Answered sagar hiremath 227 views 1 comment 0 points Most recent by Adriano Koga_20259 February 2021Community Q&A