OptiStruct

Discussion List

• 
  To find the Torque required to loosen the interference fit

  Answered Vidyaprakash G S 422 views 1 comment 0 points Most recent by Adriano_Koga August 2021Community Q&A
• 
  How to output H3D displacement with PEAKOUT for a frequency response subcase

  Question Tahsin Chowdhury_22204 298 views 0 comments 0 points Most recent by Tahsin Chowdhury_22204 August 2021Community Q&A
• 
  Minimum Tape Length Freesize constraint

  Answered Andrew Atkinson 368 views 4 comments 0 points Most recent by Andrew Atkinson August 2021Community Q&A
• 
  Error #3423

  Answered Vidyaprakash G S 3.7K views 1 comment 0 points Most recent by Adriano_Koga August 2021Community Q&A
• 
  Wrong Material Orientation ?

  Answered Pawel_22615 422 views 2 comments 0 points Most recent by Pawel_22615 August 2021Community Q&A
• 
  How can I start optistruct on version 2021.1 under linux?

  Answered Walter Reis_21132 222 views 1 comment 0 points Most recent by RobHoglund August 2021Community Q&A
• 
  Learning Qualitative Design Criteria

  Eamon Whalen 600 views 1 comment 1 point Most recent by Joseph Pajot August 2021Other Discussion & Knowledge
• 
  How to setup Altair compute console with remote job submissions

  pravarth 137 views 0 comments 0 points Most recent by pravarth August 2021Altair HyperWorks
• 
  How to create a flexibody for use in a MotionView-EDEM co-simulation?

  Answered Hugh Smith 665 views 4 comments 0 points Most recent by Praful August 2021Community Q&A
• 
  How to restart the dynamic analysis in optistruct?

  Answered shivaswamy gurusiddaiah_22438 347 views 3 comments 0 points Most recent by Adriano_Koga August 2021Community Q&A
• 
  構造最適化 2021 入門 トレーニングビデオ

  Imoto 1.3K views 0 comments 2 points Most recent by Imoto August 2021Altair HyperWorks - 日本語
• 
  線形構造解析 2021 入門 トレーニングビデオ

  Imoto 1.6K views 0 comments 2 points Most recent by Imoto August 2021Altair HyperWorks - 日本語
• 
  Getting high stress in contact interface

  Answered Vidyaprakash G S 482 views 3 comments 0 points Most recent by Adriano_Koga August 2021Community Q&A
• 
  Contact penetration

  Answered Vidyaprakash G S 582 views 1 comment 0 points Most recent by Adriano_Koga August 2021Community Q&A
• 
  Error code9

  Question T_20827 56 views 0 comments 0 points Most recent by T_20827 July 2021Community Q&A
• 
  export .fem file with Include Files in model

  Answered zeynepbkurt 688 views 2 comments 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  multi-model optimization

  Answered HitenChauhan21 193 views 1 comment 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  0D mass element graphics location

  Accepted ✓ Casper Kruger 306 views 2 comments 0 points Most recent by Jason_Craanen July 2021Community Q&A
• 
  QVOL heat generation

  Accepted ✓ Adib Adzaman 231 views 8 comments 0 points Most recent by Adib Adzaman July 2021Community Q&A
• 
  Why is the displacement of my model is extremely high?

  Answered Manuel_21421 693 views 5 comments 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  How to select a node in space to give ambient temperature (Linear Steady State Heat Transfer)?

  Answered Ajay_22186 462 views 3 comments 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  MATFAT paramaters for AL7075 T6

  Answered Matteo_22491 478 views 1 comment 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  Line Load

  Accepted ✓ Casper Kruger 475 views 1 comment 0 points Most recent by Hakan_20716 July 2021Community Q&A
• 
  contact resistance

  Answered Adib Adzaman 144 views 1 comment 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  Adding loads to model from excel table

  Accepted ✓ Casper Kruger 90 views 1 comment 0 points Most recent by Adriano_Koga July 2021Community Q&A
• 
  FRF Analysis: Load phase angle as DESVAR

  Question Sebastian_21522 165 views 0 comments 0 points Most recent by Sebastian_21522 July 2021Community Q&A
• 
  How can I compute a force vector from a displacement

  Answered Minsik Seo 277 views 1 comment 0 points Most recent by fujita July 2021Community Q&A
• 
  degree of freedom of the electrode

  Answered Adib Adzaman 115 views 1 comment 0 points Most recent by Rogerio Nakano_21179 July 2021Community Q&A
• 
  Optistruct error #802

  Answered Altair Forum User 892 views 2 comments 1 point Most recent by Altair Forum User July 2021Community Q&A
• 
  Exporting stress results from Print3D to Optistruct

  Answered ks prasanna 1.1K views 7 comments 0 points Most recent by Angel Limon July 2021Community Q&A