OptiStruct

Discussion List

• 
  Constraints in multi-material topology optimization

  Accepted ✓ Reza Karshenas 146 views 3 comments 0 points Most recent by Xiaolei December 2023Community Q&A
• 
  Mode Tracking in GSO

  Answered Torben0159 462 views 3 comments 0 points Most recent by Adriano Koga_20259 November 2023Community Q&A
• 
  I want to apply pretension load on a model and then apply a temperature load and see the resulting expansion due to temperature load.

  Answered Shiva Prasad 112 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  シェルモデルのトポロジー最適化

  Answered Shimada_21103 173 views 1 comment 0 points Most recent by N_Akagawa November 2023Community Q&A
• 
  Non-interactive command line interface

  Answered Danilo Moretti_20542 205 views 2 comments 1 point Most recent by etembras November 2023Community Q&A
• 
  質問担当者の確認方法

  Question Shimada_21103 213 views 0 comments 0 points Most recent by Shimada_21103 November 2023Community Q&A
• 
  2D Stator model press fit Simulation boundary conditions

  Answered Junhyeong Kang 272 views 5 comments 0 points Most recent by Junhyeong Kang November 2023Community Q&A
• 
  Optistruct analysis does not shoe any displacement or stress data

  Answered Kanishka Kahanthen 147 views 1 comment 0 points Most recent by Xiaolei November 2023Community Q&A
• 
  compliance in static analysis results

  Accepted ✓ Reza Karshenas 185 views 1 comment 0 points Most recent by Adriano_Koga November 2023Community Q&A
• 
  Campbell Diagram with 3D Rotor Dynamics Model

  Accepted ✓ Athanasios Besikiotis 510 views 2 comments 0 points Most recent by Athanasios Besikiotis November 2023Community Q&A
• 
  press fit simulation of 2D Stator model in Optistruct

  Answered Junhyeong Kang 178 views 1 comment 0 points Most recent by Adriano_Koga November 2023Community Q&A
• 
  PNORM in Topology Optimization

  Answered Reza Karshenas 193 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Easiest way to install OptiStruct on MacOs with M1 Pro chip trough Windows

  Answered Mattia Fianco 142 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Press fit simulation of 2D 1/6 Stator Model Constraints?

  Answered Junhyeong Kang 228 views 1 comment 0 points Most recent by Unknown November 2023Community Q&A
• 
  Optistruct Timeout ALARM. OUT File shows no error

  Answered csymo950 570 views 2 comments 0 points Most recent by loistf November 2023Community Q&A
• 
  [SimLab] CNTNLSUB를 사용한 연속 해석 설정 방법

  sohyung 52 views 0 comments 0 points Most recent by sohyung November 2023Altair HyperWorks - 한국어
• 
  *** INTERNAL PROGRAMMING ERROR *** in file "automset.F", at location # 241.

  Answered Evan Nagy 636 views 1 comment 0 points Most recent by Xiaolei November 2023Community Q&A
• 
  Altair HyperWorks Hardware and system requirements

  Michael Herve 8.6K views 0 comments 3 points Most recent by Michael Herve November 2023Altair HyperWorks
• 
  ENCRYPTING MATERIAL FILE in OPTISTRUCT 21/17

  Answered Manmohan 517 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Free radiation thermal analysis

  Answered Chase McLaughlin 337 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Stress base Topology Optimization

  Accepted ✓ Reza Karshenas 311 views 2 comments 0 points Most recent by GTT Johan November 2023Community Q&A
• 
  Creating Result Comparisons Graphs for Topology Optimizations

  Accepted ✓ Reza Karshenas 195 views 2 comments 0 points Most recent by GTT Johan November 2023Community Q&A
• 
  Enter a Material instead of a Property in DRESP1 volumefrac entry

  Answered Lukas Kneer_21880 248 views 1 comment 0 points Most recent by etembras November 2023Community Q&A
• 
  Filament Winding Modeling in Optistruct

  Answered Giordan Pantaleo 192 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Define a heat flux

  Answered Alvaro Rodriguez_20950 290 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  How to optimize using DRESP3 response ?

  Answered yuankun hu 227 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Density of all element as input for DRESP3

  Answered Nicolò Lodini_21379 132 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  PSHELL Formulation for Multiple MIDs

  Answered Justin Morris 293 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  Optistruct 2022 (error while running a simulation - 3 point bending on a composite test sample)

  Answered Nrupa Chandra 415 views 1 comment 0 points Most recent by loistf November 2023Community Q&A
• 
  How can i produce topology optimisation of a wingbox? i have the 3d model and i put it in hypermesh, i want to reduce material to reduce overall weight of wing and to increase lift.

  Answered digitald 112 views 1 comment 0 points Most recent by GTT Johan November 2023Community Q&A