OptiStruct

Discussion List

• 
  Non frozen contacts on non linear inertia relief - possibility to update contacts between subcases?

  Question Diego Monteverde_21242 201 views 0 comments 0 points Most recent by Diego Monteverde_21242 November 2021Community Q&A
• 
  How to analyze model after multi material topology optimization

  Question Keita 321 views 0 comments 0 points Most recent by Keita November 2021Community Q&A
• 
  Pre-tension note

  Question Casper Kruger 359 views 0 comments 0 points Most recent by Casper Kruger November 2021Community Q&A
• 
  1d Beam element Optistruct

  Question Tsherig 94 views 1 comment 0 points Most recent by Rogerio Nakano_21179 November 2021Community Q&A
• 
  【NVH】CMSとCDSの組合せによる固有値パラメータスタディの超高速化

  Sonoda 323 views 0 comments 1 point Most recent by Sonoda November 2021Altair HyperWorks - 日本語
• 
  AcuSolve : 流体構造連成（DC-FSI）チュートリアル「ACU-T:5403」

  Masu 231 views 0 comments 0 points Most recent by Masu November 2021Altair HyperWorks - 日本語
• 
  How to write an equation of gasket pressure variance for topology optimization response？

  Question Travis_20917 172 views 0 comments 0 points Most recent by Travis_20917 November 2021Community Q&A
• 
  How do I get elemental strain energy output for all elements (2D and 3D as well)?

  Answered Rachit Semalty 399 views 2 comments 0 points Most recent by Rachit Semalty November 2021Community Q&A
• 
  Can some one help me with the optimization of pin fins. I have a 2D plate and I am unable to apply heat flux to the selected elements.

  Question Vishnu Ganesan 220 views 0 comments 0 points Most recent by Vishnu Ganesan November 2021Community Q&A
• 
  Optistruct - AWS cost optimization study

  pravarth 144 views 0 comments 3 points Most recent by pravarth November 2021Altair HyperWorks
• 
  Label STRESS is missing on FATPARM card.

  Answered Abdul Muizz Jamal 374 views 3 comments 0 points Most recent by Abdul Muizz Jamal November 2021Community Q&A
• 
  Is there any way to get bending wave speed through Optistruct or any other Altair product?

  Question Sanit Bhatkar_21192 833 views 0 comments 0 points Most recent by Sanit Bhatkar_21192 November 2021Community Q&A
• 
  How do I get elemental strain energy output for all elements (2D and 3D as well)?

  Answered Rachit Semalty 1.4K views 2 comments 0 points Most recent by Rachit Semalty November 2021Community Q&A
• 
  Optistruct not installed

  Answered Lena Smole 368 views 2 comments 0 points Most recent by Lena Smole November 2021Community Q&A
• 
  When performing a composite (laminate) optimization, I Cannot see in the sizing80.fem the set related to the superply even tough I set the FZSTOSZ option in the output. How can I fix this issue?

  Question 1234 145 views 0 comments 0 points Most recent by 1234 November 2021Community Q&A
• 
  Sequencial analysis in NLtrans

  Question Vidyaprakash G S 295 views 1 comment 0 points Most recent by Gildas GUILLY_21156 November 2021Community Q&A
• 
  How do i know which MAT in optistruct to define my material property?

  Answered ✓ Paphatsorn 422 views 4 comments 0 points Most recent by Paphatsorn November 2021Community Q&A
• 
  How to avoid generating free parts (separate parts) in topology optimization?

  Question WEIKANG SONG 368 views 1 comment 0 points Most recent by Gildas GUILLY_21156 November 2021Community Q&A
• 
  ERROR 14: Missing DESVAR # 1 referenced by DRESP3 # 2.

  Answered Anatole Morcos 735 views 2 comments 0 points Most recent by Anatole Morcos November 2021Community Q&A
• 
  DRESP3 - how to get the center of mesh element and how to use DESVAR ?

  Question Anatole Morcos 202 views 1 comment 0 points Most recent by Ben Buchanan November 2021Community Q&A
• 
  Parts and Instances functionality in Optistruct

  Naren 189 views 0 comments 1 point Most recent by Naren October 2021Altair HyperWorks
• 
  Model runs for analysis but not for optimization

  Answered Stéphane C. 266 views 2 comments 0 points Most recent by Robert Hoglund October 2021Community Q&A
• 
  Ground Simulation and Contact Problems

  Answered Nayara Lacerda 254 views 2 comments 0 points Most recent by Adriano A. Koga October 2021Community Q&A
• 
  Transient thermal linear analysis - Choosing right values for PCONV group

  Question Agasttya Dixit 388 views 1 comment 0 points Most recent by Adriano A. Koga October 2021Community Q&A
• 
  Hyperworks – Introduction of Load Step Inputs card collector for Optistruct user profile

  Alberto Campagna_20590 236 views 0 comments 2 points Most recent by Alberto Campagna_20590 October 2021Altair HyperWorks
• 
  Modeling Virtual Fluid Mass in OptiStruct with MFLUID

  Robert Hoglund 2.3K views 0 comments 1 point Most recent by Robert Hoglund October 2021Altair HyperWorks
• 
  How to divide an Optistruct run on multiple scratch disks.

  FredrikI_21476 57 views 0 comments 0 points Most recent by FredrikI_21476 October 2021Altair HyperWorks
• 
  Shape Controls - Symmetric Plans does reduce my solution time when inserted on the model? - Topology Optimization

  Question Diogo Vicente_21694 285 views 1 comment 0 points Most recent by Robert Hoglund October 2021Community Q&A
• 
  Risks of Using CBAR Elements | Just use CBEAM Elements Instead

  BenB_22580 524 views 0 comments 1 point Most recent by BenB_22580 October 2021Altair HyperWorks
• 
  3 Step Composite Optimization Cheat Sheet: Shape, Size, Shuffle

  Lacie Feller_21296 1.6K views 0 comments 2 points Most recent by Lacie Feller_21296 October 2021Altair HyperWorks