English

Discussion List

• 
  Do you want to learn more about Inspire? There is a dedicated eLearning course on learn.altair.com!

  liz_w 274 views 0 comments 0 points Most recent by liz_w April 2024Altair HyperWorks
• 
  How to combine multiple topography databases to be used in a Rural scenario

  Zeina 85 views 0 comments 0 points Most recent by Zeina April 2024Altair HyperWorks
• 
  Specifying cumulative particle size distribution

  Answered Raïsa Roeplal 328 views 3 comments 0 points Most recent by jerrinjobs April 2024Community Q&A
• 
  Get the SINR value of each base station or antenna

  Answered Võ Trí_21292 217 views 3 comments 0 points Most recent by Reiner_Hoppe April 2024Community Q&A
• 
  What does this lenght indicate in Motion view in 2023.1

  Accepted ✓ Tejas 268 views 4 comments 0 points Most recent by GTT Adam April 2024Community Q&A
• 
  Why? Penetration VS Initial Penetration

  Accepted ✓ Sebastian Yang 433 views 6 comments 0 points Most recent by Polyvios Romanidis April 2024Community Q&A
• 
  Undo function misbehaving

  Answered AM_20700 565 views 3 comments 0 points Most recent by Chayan April 2024Community Q&A
• 
  Do inspire cast take into account vent on overflow

  Answered Normand Savard 304 views 4 comments 0 points Most recent by Normand Savard April 2024Community Q&A
• 
  LICENSE STUDENT

  Answered Giovana Garcia 190 views 1 comment 0 points Most recent by Payal Pawar_20288 April 2024Community Q&A
• 
  AutoSave tcl in HyperMesh 2023.1

  Answered Kwangsu_Kim 287 views 2 comments 0 points Most recent by Kwangsu_Kim April 2024Community Q&A
• 
  Is there a way to split a file up into smaller sizes using DPS?

  Answered lsojat 160 views 2 comments 0 points Most recent by CPorthouse April 2024Community Q&A
• 
  FEKO (student edition) solver error message "Error 20103"

  Answered John. Lee 723 views 4 comments 0 points Most recent by Mel April 2024Community Q&A
• 
  Consumer Electronics Drop Testing. Part 4: HyperStudy Setup

  Christopher_Fadanelli 169 views 0 comments 0 points Most recent by Christopher_Fadanelli April 2024Altair Exchange
• 
  Can a TEMP load be used to run a buckling analysis?

  Answered Jay Tudor 371 views 1 comment 0 points Most recent by RobHoglund April 2024Community Q&A
• 
  Particle Heat Generation?

  Answered Clemenslischka 303 views 3 comments 0 points Most recent by Stephen Cole April 2024Community Q&A
• 
  Why are my particles disappearing while simulation although my time step is 20%

  Answered Sabiar Sonet 215 views 1 comment 0 points Most recent by PrasadAvilala April 2024Community Q&A
• 
  Visualization error in review element orientations pannel

  Answered Rafal Blasczykowski 172 views 1 comment 0 points Most recent by Jason_Craanen April 2024Community Q&A
• 
  Can I use ANN in Flux to detect fault for a SynRM motor?

  Answered Truc Hoang Ho 204 views 2 comments 0 points Most recent by Truc Hoang Ho April 2024Community Q&A
• 
  My solution ratio doesn't converge, some advices to improve it?

  Answered Marco Alfonso Diaz Neciosup 504 views 3 comments 0 points Most recent by Marco Alfonso Diaz Neciosup April 2024Community Q&A
• 
  Multi-Reflection Simulations in Dual-Foci System

  Answered artgru 279 views 6 comments 0 points Most recent by artgru April 2024Community Q&A
• 
  Set geometry cleanup tolerance in script

  Answered ATLURI BHARATH KUMAR 167 views 2 comments 0 points Most recent by Michael Herve April 2024Community Q&A
• 
  RADIOSS JOB FAILED and no Engine Output File generated

  Answered Jose Luis Barrera_21161 188 views 2 comments 0 points Most recent by Jose Luis Barrera_21161 April 2024Community Q&A
• 
  How to write a Lua script in Postfeko

  Answered yun tianyu 167 views 1 comment 0 points Most recent by Torben Voigt April 2024Community Q&A
• 
  How to define Area Loads in S-TIMBER

  Matthew_Sauer1 43 views 0 comments 0 points Most recent by Matthew_Sauer1 April 2024Altair HyperWorks
• 
  How can i simulate 2D and 3D elements in the same model?

  Answered RafaelC_21253 280 views 7 comments 0 points Most recent by RafaelC_21253 April 2024Community Q&A
• 
  Hi, can anyone help to please identify the orientation i.e. X, Y, Z, RX, RY, RZ directions of the compliant universal joint in the images attached? - (joint is as per front lower control arm unv joint from multilink template)

  Accepted ✓ Tahsin Chowdhury_21670 227 views 8 comments 0 points Most recent by GTT Adam April 2024Community Q&A
• 
  Student Altair Hyperworks License migration

  Accepted ✓ Edoardo Caroti 362 views 2 comments 0 points Most recent by Edoardo Caroti April 2024Community Q&A
• 
  Educational access to the legacy version of Hypermesh

  Answered Max_21123 151 views 1 comment 0 points Most recent by Payal Pawar_20288 April 2024Community Q&A
• 
  How to simulate a non-flat surface

  Answered Mathilde Roig 205 views 1 comment 0 points Most recent by ChristophM April 2024Community Q&A
• 
  How can I solve the problem of importing CAD geometry?

  Answered Iwona Wyrebska_20857 679 views 6 comments 0 points Most recent by Stephen Cole April 2024Community Q&A