English

Discussion List

• 
  How to write a Lua script in Postfeko

  Answered yun tianyu 167 views 1 comment 0 points Most recent by Torben Voigt April 2024Community Q&A
• 
  How to define Area Loads in S-TIMBER

  Matthew_Sauer1 41 views 0 comments 0 points Most recent by Matthew_Sauer1 April 2024Altair HyperWorks
• 
  How can i simulate 2D and 3D elements in the same model?

  Answered RafaelC_21253 284 views 7 comments 0 points Most recent by RafaelC_21253 April 2024Community Q&A
• 
  Hi, can anyone help to please identify the orientation i.e. X, Y, Z, RX, RY, RZ directions of the compliant universal joint in the images attached? - (joint is as per front lower control arm unv joint from multilink template)

  Accepted ✓ Tahsin Chowdhury_21670 238 views 8 comments 0 points Most recent by GTT Adam April 2024Community Q&A
• 
  Student Altair Hyperworks License migration

  Accepted ✓ Edoardo Caroti 364 views 2 comments 0 points Most recent by Edoardo Caroti April 2024Community Q&A
• 
  Educational access to the legacy version of Hypermesh

  Answered Max_21123 154 views 1 comment 0 points Most recent by Payal Pawar_20288 April 2024Community Q&A
• 
  How to simulate a non-flat surface

  Answered Mathilde Roig 207 views 1 comment 0 points Most recent by ChristophM April 2024Community Q&A
• 
  How can I solve the problem of importing CAD geometry?

  Answered Iwona Wyrebska_20857 692 views 6 comments 0 points Most recent by Stephen Cole April 2024Community Q&A
• 
  Python block in altair activate

  Accepted ✓ Linn Liao 225 views 2 comments 0 points Most recent by Linn Liao April 2024Community Q&A
• 
  Steady-State Detector for Early Stop in Twin Activate

  RSGarciarivas 92 views 0 comments 0 points Most recent by RSGarciarivas April 2024Altair Exchange
• 
  S-FRAME 2024 Release Highlights

  Matthew_Sauer1 491 views 0 comments 2 points Most recent by Matthew_Sauer1 April 2024Altair HyperWorks
• 
  Optimal way to mesh my 3D model (3 phase conductors in an aluminum barrier with flux plates)

  Answered alexandre pelletier 168 views 4 comments 0 points Most recent by Lavanya Vadamodala_20519 April 2024Community Q&A
• 
  Acusolve parrallel run

  Accepted ✓ Vikas Kaprwan 232 views 1 comment 0 points Most recent by acupro April 2024Community Q&A
• 
  Hyperstudy Optima Results Terms

  Accepted ✓ Andreas_H 253 views 2 comments 0 points Most recent by Adriano_Koga April 2024Community Q&A
• 
  Flux Skew 2022.3 without "Sensor" section

  Answered Gianluca 289 views 3 comments 0 points Most recent by Gianluca April 2024Community Q&A
• 
  Contact interference

  Answered Gasmi Cherif 304 views 4 comments 0 points Most recent by Adriano_Koga April 2024Community Q&A
• 
  Announcing Altair Grid Engine 2024.1.0 (8.9.0)

  Andy Schwierskott_22306 677 views 0 comments 1 point Most recent by Andy Schwierskott_22306 April 2024Altair HPCWorks
• 
  Error # 2148

  Answered Altair Forum User 7.6K views 20 comments 0 points Most recent by Altair Forum User April 2024Community Q&A
• 
  How to define feeder length,portholes length weld chamber length... based on 2D?

  Question Brian_20847 378 views 1 comment 0 points Most recent by DO HAI HONG April 2024Community Q&A
• 
  モーション接触の接触剛性の値をテーブル形式で設定することは可能でしょうか？

  Answered 真鍋 一平 191 views 1 comment 0 points Most recent by Kosuke_IKEDA April 2024Community Q&A
• 
  Can HyperWorks run the Abaqus Topology Optimization?

  Answered Golden_Tan 253 views 4 comments 0 points Most recent by Paulo Libório April 2024Community Q&A
• 
  Absolute/relative pressure offset - CFD

  Answered LZanell 626 views 4 comments 0 points Most recent by LZanell April 2024Community Q&A
• 
  So, we just have been signed up for Altair and we have been using Monarch. Need help setting up

  Answered Richard Tamblyn 142 views 1 comment 0 points Most recent by Rebecca_Cronin April 2024Community Q&A
• 
  Apply pressure on a 3D meshed surface avoiding the edges

  Answered Pablo Sevilla 271 views 2 comments 0 points Most recent by Jason_Craanen April 2024Community Q&A
• 
  Is it possible to implement yield-2000 model in Inspire Form?

  Answered rm_21223 180 views 1 comment 0 points Most recent by Saurabh_Bhamania April 2024Community Q&A
• 
  Someone can help me with this error? "CONTACT interface 1 has Secondary node 6264 that lies exactly on the Main surface with OPENGAP option. Impossible to define pushout direction."

  Answered RafaelC_21253 564 views 1 comment 0 points Most recent by Jason_Craanen April 2024Community Q&A
• 
  Where can I find Keyword cards for Optistruct

  Answered RandyH 251 views 1 comment 0 points Most recent by Jason_Craanen April 2024Community Q&A
• 
  Two surface with different numbers of nodes

  Answered ROSA CATANEO 220 views 2 comments 0 points Most recent by Jason_Craanen April 2024Community Q&A
• 
  Motion view file opening

  Accepted ✓ Tejas 338 views 4 comments 0 points Most recent by Tejas April 2024Community Q&A
• 
  Altair.com error

  Answered Ts Faridah Yahya 156 views 2 comments 0 points Most recent by KM_ALTR April 2024Community Q&A