Radioss

How to use /TH/MODE??

Answered gslee 429 views 2 comments 0 points Most recent by gslee November 2019Community Q&A
How to apply an initial velocity along vector

Answered el_torstinho 398 views 2 comments 0 points Most recent by Simon Križnik November 2019Community Q&A
No Animation files being created

Answered JKL_20609 831 views 6 comments 0 points Most recent by Simon Križnik October 2019Community Q&A
property ID definition .

Answered akasht 471 views 1 comment 0 points Most recent by Simon Križnik October 2019Community Q&A
Prop/Type17 plyxfem and Mint_IDi are not visible

Answered xrek 635 views 3 comments 0 points Most recent by xrek October 2019Community Q&A
ERROR 760 help

Answered Samuele 440 views 1 comment 0 points Most recent by Simon Križnik October 2019Community Q&A
Composite - mat orientations, xfem/delamination

Answered Altair Forum User 1.7K views 5 comments 0 points Most recent by Altair Forum User October 2019Community Q&A
INCOMPATIBLE KINEMATIC CONDITIONS IN MODEL DESCRIPTION :

Answered Kunal Hirudkar 1K views 2 comments 0 points Most recent by Simon Križnik October 2019Community Q&A
USER MATERIAL SUBROUTINE

Answered Altair Forum User 4K views 7 comments 0 points Most recent by Rahul Rajan_21763 October 2019Community Q&A
Negative % ERROR IN RADIOSS

Answered NoorAlam_08 1.3K views 8 comments 0 points Most recent by Simon Križnik October 2019Community Q&A
The reason why run file stops after 1 cycle?

Answered gslee 469 views 2 comments 0 points Most recent by gslee September 2019Community Q&A
FORCE VS DISPLACEMENT GRAPH AND TIME VS DISPLACEMENT GRAPH

Answered NoorAlam_08 1.4K views 7 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
Rigid Bolt with Spring and Pretension

Answered gslee 2.3K views 2 comments 0 points Most recent by gslee September 2019Community Q&A
Is it possible to activate boundary condition at certain time?

Answered gslee 619 views 1 comment 0 points Most recent by Simon Križnik September 2019Community Q&A
Delete element before impact

Answered Toon 630 views 1 comment 0 points Most recent by Andy_20955 September 2019Community Q&A
Where is theory manual about interface type 24?

Answered gslee 525 views 2 comments 0 points Most recent by gslee September 2019Community Q&A
missing normal termination

Answered Altair Forum User 3.6K views 20 comments 0 points Most recent by Altair Forum User September 2019Community Q&A
the " error in sph decomp" in radioss?

Answered meng2019 498 views 2 comments 0 points Most recent by Crashphys September 2019Community Q&A
Time Step Less or Equal Zero Error

Answered Altair Forum User 1.8K views 6 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
radioss calculating time steps for high speed impact

Answered meng2019 946 views 8 comments 0 points Most recent by Andy_20955 September 2019Community Q&A
Radioss Run Error

Answered gopal_rathore 3.2K views 7 comments 0 points Most recent by gopal_rathore September 2019Community Q&A
重力の設定について

Answered Kohta Ito_20796 2.3K views 2 comments 0 points Most recent by Altair_Ichikawa September 2019質問と回答 (Q&A)
Imposed Temperature on a thermobimetal plate

Answered Schorsch 694 views 3 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
Axisymmetric Analysis in Radioss

Answered Chethan Y C 885 views 1 comment 0 points Most recent by Simon Križnik September 2019Community Q&A
Creation of the card /INISHE/ORTH_LOC

Answered Enrico Mestieri 543 views 1 comment 0 points Most recent by Simon Križnik September 2019Community Q&A
Modelling of creep effect:

Answered JJJ 1.3K views 5 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
Determine Equivalent Static Loads in RADIOSS

Answered Crashphys 1.5K views 11 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
Warning ID 760

Answered Schorsch 1.3K views 6 comments 0 points Most recent by Simon Križnik September 2019Community Q&A
Fpenmax is only applied on initial penetration?

Answered gslee 441 views 2 comments 0 points Most recent by gslee August 2019Community Q&A
Is it impossible to set perfectly no relative motion using /INTER/TYPE2?

Answered gslee 514 views 2 comments 0 points Most recent by Simon Križnik August 2019Community Q&A

Upcoming Events

Altair HyperMesh - Introduction to New Interface and Technology Monthly Series
Each of the sessions has the same content and is meant to give an overview over new tools and technologies in HyperMesh as well as a practical introduction to the user interface. Sessions occur every second Thursday of each month from 9 AM to 12 PM CET, including a 15-minute break. Registration is now open for the…
HF Session 13 - Designing Frequency Selective Surfaces (FSS) and modelling Radomes with characterized surfaces in Al
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to design Frequency Selective Surfaces (FSS) in Altair Feko? 2) How to model Radomes with…
HF Session 14 - Performing optimization using Altair Feko & advanced optimization features with Altair Hyperstudy
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to perform optimization using Altair Feko? 2) Advanced optimization using Feko and HyperStudy We will…
HF Session 15 - Overcoming meshing challenges and insight on effective techniques for CAD Cleanup in Altair Feko
In this session, you will learn: 1) How to fix meshing errors in Altair Feko? 2) Tips and tricks on how to clean CAD in Altair Feko We will allow for 10 mins of Q&A after the presentation. This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here:

Radioss

Discussion List