OptiStruct

Discussion List

• 
  Transient Modal Dynamic with Displacement Base Motion - Optistruct

  Answered Jeganathan 111 views 4 comments 0 points Most recent by Jeganathan March 12Community Q&A
• 
  how can I solve this problem, after Lattice Optimization?

  Question Francesco_22534 113 views 1 comment 0 points Most recent by Nicola_Cardone March 10Community Q&A
• 
  Residual vector を理解する例題、その2

  altair_fukuoka 109 views 1 comment 0 points Most recent by altair_fukuoka March 10Altair Exchange
• 
  Residual vector を理解する例題、その3

  altair_fukuoka 76 views 0 comments 0 points Started by altair_fukuoka March 10 Altair Exchange
• 
  Residual vector を理解する例題、その1

  altair_fukuoka 232 views 1 comment 0 points Most recent by altair_fukuoka March 10Altair Exchange
• 
  Fluid Modeling with OptiStruct

  Alberto Campagna 191 views 0 comments 2 points Started by Alberto Campagna March 7 Altair HyperWorks
• 
  DUCTILE DAMAGE INITIATION AND EVOLUTION (INIEVO) IN OPTISTRUCT IMPLICIT-EXPLICIT

  solon 683 views 1 comment 1 point Most recent by solon March 7Altair HyperWorks
• 
  Example to control stress output position in PBEAM

  altair_fukuoka 155 views 0 comments 3 points Started by altair_fukuoka March 7 Altair Exchange
• 
  Rover Design & Analysis using Altair Inspire

  John_Dagg_0 222 views 0 comments 2 points Started by John_Dagg_0 March 6 Altair Exchange
• 
  How does the LMTGAP gap limit value is calculated for contact stabilization?

  Answered Arun_idhunaal 79 views 1 comment 0 points Most recent by Marina_Lima March 6Community Q&A
• 
  I am facing some difficulties in optimization for plastic components.

  Answered Lokeshgndec 11 views 1 comment 0 points Most recent by Adriano_Koga March 6Community Q&A
• 
  Why is my .disp file empty?

  Accepted ✓ Sebastian_981 55 views 2 comments 0 points Most recent by solon March 6Community Q&A
• 
  RBE3 に強制変位を与えても動く理由を示す例題

  altair_fukuoka 186 views 0 comments 1 point Started by altair_fukuoka March 6 Altair Exchange
• 
  Issues in Structural Analysis of Gasket (Si) and Subgasket (PEN)

  Answered julia4567 31 views 1 comment 0 points Most recent by GTT Johan March 5Community Q&A
• 
  Torsional spring: preload

  Answered Alice7 97 views 1 comment 0 points Most recent by FaroukMaabs March 5Community Q&A
• 
  Optistruct:Very low CPU utilization rate

  Answered ZXG 41 views 1 comment 0 points Most recent by Kranzeder March 5Community Q&A
• 
  GRAV card in Topology Optimization

  Accepted ✓ Vladimir_Gantovnik 395 views 4 comments 0 points Most recent by shuxin March 4Community Q&A
• 
  Rollover Simulation using EDEM-MS Two-way Coupling

  PrasadAvilala 133 views 0 comments 0 points Started by PrasadAvilala March 3 Altair HyperWorks
• 
  Error 14: Property is missing

  Accepted ✓ Xiang 100 views 2 comments 0 points Most recent by Xiang March 3Community Q&A
• 
  *** ERROR # 2786 *** AMSES requires V2 to be set in EIGRA data

  Accepted ✓ Sebastian_981 31 views 2 comments 0 points Most recent by Sebastian_981 February 28Community Q&A
• 
  Condensation using CMS method(CMSMETH)

  Answered REDDYRAMU 39 views 1 comment 0 points Most recent by solon February 28Community Q&A
• 
  Ensuring support of non-design regions in topology optimization

  Answered Sezek_O 56 views 3 comments 0 points Most recent by Sezek_O February 27Community Q&A
• 
  Is it possible to apply constant pressure and acceleration in Modal FRF analysis in Optistruct.

  Answered Jadhav 11 views 2 comments 0 points Most recent by Jadhav February 27Community Q&A
• 
  Brake Noise Simulation Using Contact Enhanced Flexible Multibody

  GTT Erik 1.1K views 3 comments 4 points Most recent by Narasimhamurthy Shivanna February 26Altair Exchange
• 
  Altair 2025 Student Edition Shape Optimization results not showing shape change

  Answered FedericoVenturi 43 views 1 comment 0 points Most recent by Adriano_Koga February 25Community Q&A
• 
  OptiStruct not showing results

  Answered AlejandroVKL3 51 views 5 comments 0 points Most recent by AlejandroVKL3 February 24Community Q&A
• 
  Change components of existing element

  Accepted ✓ Mohamed_ABDO 191 views 1 comment 0 points Most recent by solon February 24Community Q&A
• 
  How can we get the normal vector of the surfaces obtained after mid surface extraction?

  Answered tanushi 21 views 1 comment 0 points Most recent by Michael Herve February 24Community Q&A
• 
  Co-simulation of MotionView, Optistruct Flexbody and EDEM

  Accepted ✓ PimK 89 views 1 comment 0 points Most recent by GTT Adam February 21Community Q&A
• 
  Bond Failure Theory

  Answered smandelli_LINCE 46 views 1 comment 0 points Most recent by Adriano_Koga February 20Community Q&A