Discussion List

• 
  PSIM Introduction course - Certificate of Attendance - not received - reg

  Answered Ram Prakash P 124 views 1 comment 0 points Most recent by RN February 14Community Q&A
• 
  Planetary Gearset Stress Analysis and Optimization in Inspire Motion

  John_Dagg_0 255 views 2 comments 0 points Most recent by GTT Adam February 14Altair Exchange
• 
  Transient Magnetic 2D Analysis of Coupled Inductor in Altair Flux 2025

  Accepted ✓ Adil_Sheikh 51 views 4 comments 0 points Most recent by Adil_Sheikh February 14Community Q&A
• 
  How can I get an Altair SLC Personal Edition license?

  Nico Chart_21517 482 views 9 comments 0 points Most recent by Nico Chart_21517 February 13Altair RapidMiner
• 
  MBD results to OptiStruct Fatigue for a truck

  Answered Brian_20847 315 views 1 comment 0 points Most recent by GTT Adam February 13Community Q&A
• 
  Virtual Fluid Mass

  Alberto Campagna 316 views 2 comments 1 point Most recent by Alberto Campagna February 13Altair HyperWorks
• 
  Unable to mesh port 'WirePort1'. Wires may not be embedded in PEC regions.

  Accepted ✓ Frank Asiamah 47 views 3 comments 0 points Most recent by Frank Asiamah February 13Community Q&A
• 
  I am not able to launch Feko 2023.1 student edition on Ubuntu 24.04 LTS.

  Accepted ✓ Frank Asiamah 91 views 2 comments 0 points Most recent by Frank Asiamah February 13Community Q&A
• 
  How to add an angle of twist to a beam in hypermesh?

  Answered Sanka Dasanayaka 441 views 2 comments 0 points Most recent by WagnerFEA February 13Community Q&A
• 
  Specification of list of frequencies for time domain approximate sinc signal

  Answered Altair Forum User 501 views 1 comment 0 points Most recent by mvogel February 13Community Q&A
• 
  erros in using wallman

  Answered Altair Forum User 749 views 1 comment 0 points Most recent by mvogel February 13Community Q&A
• 
  How to solve this "zero or negative yield stress encountered. nonlinear analysis cannot proceed. this issue may occur if the hardening parameter H is negative"?

  Answered Alberto CAMPUZANO 988 views 2 comments 0 points Most recent by WagnerFEA February 13Community Q&A
• 
  EDEM-HyperStudy Connector: Installers and User Guide

  Stefan Pantaleev_21979 2.7K views 5 comments 1 point Most recent by Stefan Pantaleev_21979 February 13Altair Exchange
• 
  Does Delta temperature effect the UNTC results

  Answered JAYA LAKSHMI VENUTURUMILLI 516 views 1 comment 0 points Most recent by GTT Johan February 13Community Q&A
• 
  Lattice definition in the Multiscale Designer

  Answered Mehmet Demirtunc 247 views 1 comment 0 points Most recent by GTT Johan February 13Community Q&A
• 
  How to fit the stress-strain curve obtained from simulation with experimental data

  Answered Thang 51 views 2 comments 0 points Most recent by Thang February 13Community Q&A
• 
  Electromagnetic modeling and analysis of an induction heating coil

  bvallet 100 views 1 comment 0 points Most recent by Manir February 12Altair HyperWorks
• 
  acuReport

  Answered Prabin Pradhananga_22497 141 views 1 comment 0 points Most recent by ydigit February 12Community Q&A
• 
  AcuRun Issue

  Answered Qing Huai Tai 33 views 1 comment 0 points Most recent by ydigit February 12Community Q&A
• 
  How can I identify the parameters for Jiles - Atherton model in Flux?

  Yann_Le_Floch 128 views 2 comments 1 point Most recent by Yann_Le_Floch February 11Altair HyperWorks
• 
  datasets error in physics AI

  Answered George Nessim Aziz 306 views 2 comments 0 points Most recent by ranxx February 11Community Q&A
• 
  The HyperWorks for Post-Processing Associate Specialist Badge is Now Available On learn.altair.com!

  wscott 42 views 0 comments 0 points Started by wscott February 11 Altair HyperWorks
• 
  The HyperWorks for Pre-Processing Associate Specialist Badge is Now Available on learn.altair.com!

  wscott 42 views 0 comments 0 points Started by wscott February 11 Altair HyperWorks
• 
  Aerospace - Fastener Setup Tool Question

  Answered Burner2k 788 views 3 comments 0 points Most recent by SSKG February 11Community Q&A
• 
  Access and use the free Altair Student Edition - Step 3 – Download and Install a Software from within the Student Edition Bundle of your choice

  Closed Rahul_P1 11.2K views 3 comments 1 point Most recent by Dattatreyulu February 10Academic
• 
  How to use NLFE body in full vehicle Motioview simulation

  Answered Tomas Tienstra 236 views 1 comment 0 points Most recent by GTT Adam February 7Community Q&A
• 
  Psim license activated using different HostsIDs

  Answered joao miloch 1 view 1 comment 0 points Most recent by Rahul_P1 February 7Community Q&A
• 
  How to Renew your AI Studio Licenses when it is Licensed using RapidMiner Licensing on RapidMiner.com

  Announcement Closed Rahul_P1 234 views 0 comments 1 point Most recent by Rahul_P1 October 2024Academic
• 
  Post Hole Digger: EDEM-OS Two Way Coupling

  PrasadAvilala 161 views 0 comments 0 points Started by PrasadAvilala February 5 Altair Exchange