English

Discussion List

• 
  Can I request specific grid displacements to be written to the .out file?

  Accepted ✓ nreindel 1.2K views 3 comments 0 points Most recent by nreindel January 2021Community Q&A
• 
  How to delete part of contact surface in hypermesh 2020.1?

  Accepted ✓ LIMING LI_21655 816 views 4 comments 0 points Most recent by Adriano Koga_20259 January 2021Community Q&A
• 
  Selection nodes in on a plane by .tcl macro

  Answered Mirhan Ozdemir_21843 283 views 1 comment 0 points Most recent by Adriano Koga_20259 January 2021Community Q&A
• 
  Error in Transient thermal Model

  Answered Noti 519 views 9 comments 0 points Most recent by Noti January 2021Community Q&A
• 
  Fluxmotor plots

  Answered Alvaro_21870 287 views 3 comments 0 points Most recent by fzidat January 2021Community Q&A
• 
  Query about my altair feko student edition Exceeded the limit.

  Accepted ✓ Manthan Y Ijari 235 views 1 comment 0 points Most recent by PrasannaK January 2021Community Q&A
• 
  Is it possible to set the separation force?

  Answered Mark Lin 169 views 3 comments 0 points Most recent by Gildas_GUILLY January 2021Community Q&A
• 
  Non meshed coil: Difference line - rectangle

  Answered Altair Forum User 979 views 4 comments 0 points Most recent by asoualmi January 2021Community Q&A
• 
  When extracts tabular data from pdf pages its merged first few rows and display them as table column instead of table row

  Answered Ashish D 323 views 3 comments 0 points Most recent by Ashish D January 2021Community Q&A
• 
  Missing most of the data from pdf page.

  Answered Ashish D 215 views 2 comments 0 points Most recent by Rebecca_Cronin January 2021Community Q&A
• 
  Conversion from Optistruct to Abaqus

  Answered FaroukM 894 views 2 comments 0 points Most recent by FaroukM January 2021Community Q&A
• 
  *** ERROR # 173 *** A dependent d.o.f. defined more than once in rigid element entry. GRID ID = xxx component = 1

  Answered Shamil Ali 1.8K views 1 comment 0 points Most recent by paulel_22250 January 2021Community Q&A
• 
  Forces in seam welds - is it possible to view them in welds local coordinate systems

  Answered Piotr Kozlowski 179 views 1 comment 0 points Most recent by Unknown January 2021Community Q&A
• 
  Effect of interface type7/type2 on nodal time step

  Answered Gabriela G 289 views 2 comments 0 points Most recent by Mathis January 2021Community Q&A
• 
  hyperstudy fluxmotor

  Answered RECEP YETİM 372 views 5 comments 0 points Most recent by Diana_38240 January 2021Community Q&A
• 
  Unable to see the geometry once i import step file or iges file

  Answered Unnikrishnan Divakaran 478 views 1 comment 0 points Most recent by QuyNguyenDai January 2021Community Q&A
• 
  Different behaviour between voltage circuit coupling VS current supply in windings

  Accepted ✓ Ronan CORIN 255 views 6 comments 0 points Most recent by Ronan CORIN January 2021Community Q&A
• 
  Measure Velocity and acceleration

  Answered Altair Forum User 2.2K views 17 comments 0 points Most recent by Adriano Koga_20259 January 2021Community Q&A
• 
  The Importance of Data Preparation & Analysis and How Monarch Simplifies this Process

  lekha janardhan 366 views 0 comments 0 points Most recent by lekha janardhan January 2021Altair RapidMiner
• 
  Energy Absorption too low

  Answered Denis Muhra 308 views 2 comments 0 points Most recent by Rogerio Nakano_21179 January 2021Community Q&A
• 
  Increase speed of the results module for Optistruct

  Answered James Seedorf 274 views 1 comment 0 points Most recent by QuyNguyenDai January 2021Community Q&A
• 
  common mesh at interface between 2 bodies

  Accepted ✓ IRA_EM_21745 1.5K views 2 comments 0 points Most recent by AlessioLibrandi January 2021Community Q&A
• 
  Messaging With Kafka in Altair Accelerator 2021.1.0

  Stuart Taylor_20654 681 views 0 comments 2 points Most recent by Stuart Taylor_20654 January 2021Altair HPCWorks
• 
  Error: Data source, file not found ERROR Hyperstudy-FluxMotor

  Answered Roberto_ 1.1K views 3 comments 0 points Most recent by Roberto_ January 2021Community Q&A
• 
  Random vibration analysis tutorial

  Answered Bala Reddy 1.6K views 3 comments 0 points Most recent by Adriano Koga_20259 January 2021Community Q&A
• 
  Not a Lotka-Volterra figure

  Accepted ✓ Tom_abc 222 views 3 comments 0 points Most recent by Ric_22025 January 2021Community Q&A
• 
  Connect two different meshes from the same solid

  Answered Adrunodro 1.3K views 4 comments 0 points Most recent by Viraj_Kulkarni January 2021Community Q&A
• 
  I got approved for student version of Altair. I am trying to download the link to install, but it doesn't work.

  Answered NIKHILA ALAPARTHI_21362 139 views 1 comment 0 points Most recent by Adriano Koga_20259 January 2021Community Q&A
• 
  I need API - to mesh with only Quads (using ruled option)

  Answered Jouher_20819 265 views 2 comments 0 points Most recent by QuyNguyenDai January 2021Community Q&A
• 
  Morphing a line body

  Answered Vassilis 261 views 2 comments 0 points Most recent by Viraj_Kulkarni January 2021Community Q&A