OptiStruct

Discussion List

• 
  shock mount selection and representing a system as a single degree of system

  Question mpvnaresh 234 views 0 comments 0 points Most recent by mpvnaresh March 2020Community Q&A
• 
  Center Of Gravity of a SET

  Answered Joel Rodarte 399 views 2 comments 0 points Most recent by PrasannaK March 2020Community Q&A
• 
  element size

  Answered Altair Forum User 2.4K views 11 comments 0 points Most recent by Nachiket Kadu_22143 March 2020Community Q&A
• 
  ACCEL Card Exporting Wrong?

  Answered Crashphys 389 views 1 comment 0 points Most recent by Simon Križnik March 2020Community Q&A
• 
  About HM, Flexible bodies

  Answered LOKESH KATARI 1.7K views 24 comments 0 points Most recent by LOKESH KATARI March 2020Community Q&A
• 
  Fatigue analysis

  Answered narasimhamurthy 466 views 3 comments 0 points Most recent by Koushik Chandrashekhar_21806 March 2020Community Q&A
• 
  Optistruct Requiring Too Much RAM

  Answered JRego 461 views 3 comments 0 points Most recent by QuyNguyenDai March 2020Community Q&A
• 
  CBUSH Element Error

  Accepted ✓ mecjos 4.7K views 5 comments 0 points Most recent by mecjos March 2020Community Q&A
• 
  Contact stress: Hertz theory vs FEA

  Question MScipio 786 views 0 comments 0 points Most recent by MScipio March 2020Community Q&A
• 
  Minimising compliance

  Answered Aadit 428 views 1 comment 0 points Most recent by Crashphys March 2020Community Q&A
• 
  Nonlinear large displacement direct transient analysis problem

  Question paula94 483 views 0 comments 0 points Most recent by paula94 March 2020Community Q&A
• 
  ERROR # 1812 - Size Optimization

  Answered Altair Forum User 3.4K views 2 comments 0 points Most recent by Rahul Rajan_21763 February 2020Community Q&A
• 
  Dynamic stiffness from frequency response analysis

  Answered sravankumar 1.1K views 1 comment 0 points Most recent by PrasannaK February 2020Community Q&A
• 
  Coupling thermal and CFD results

  Answered gopal_rathore 712 views 5 comments 0 points Most recent by Rahul Rajan_21763 February 2020Community Q&A
• 
  Coordinate System CORD2R vs CORD3R Difference?

  Answered Joel Rodarte 1.2K views 2 comments 0 points Most recent by Simon Križnik February 2020Community Q&A
• 
  *** SYSTEM ERROR *** Signal 11 :: SIGTERM

  Answered puneet.shahare 2.7K views 2 comments 0 points Most recent by QuyNguyenDai February 2020Community Q&A
• 
  Modal Frequency response analysis

  Answered sravankumar 703 views 9 comments 0 points Most recent by sravankumar February 2020Community Q&A
• 
  bushing boundary conditions - Revisited: High stresses

  Answered mvass 298 views 1 comment 0 points Most recent by mvass February 2020Community Q&A
• 
  How to request Reaction Force on a node on a static analysis

  Answered Prithvi_Raj 2.9K views 1 comment 0 points Most recent by Tommy_21858 February 2020Community Q&A
• 
  Problem with constrained modal calculation

  Answered Dan Bostwick 250 views 1 comment 0 points Most recent by Dan Bostwick February 2020Community Q&A
• 
  CNTNLSUB

  Answered mpvnaresh 1.1K views 3 comments 0 points Most recent by Tommy_21858 February 2020Community Q&A
• 
  HOW TO HANDLE SYMMETRY CONSTRAINTS AND RBE3 COUPLINGS | ERROR #2933

  Question alex_ander 1.7K views 0 comments 0 points Most recent by alex_ander February 2020Community Q&A
• 
  CONM2 negative diagonal term

  Question X2Murugesan, Arjun (A.) 318 views 0 comments 0 points Most recent by X2Murugesan, Arjun (A.) February 2020Community Q&A
• 
  RBE2 Constraints & CBEAM

  Answered Oguzhan Coban 1.1K views 1 comment 0 points Most recent by Merula_20758 February 2020Community Q&A
• 
  Error #13

  Answered Jebunderscore 1.4K views 1 comment 0 points Most recent by FaroukM February 2020Community Q&A
• 
  Inertia Relief not working properly

  Answered Pedro Neves 595 views 1 comment 0 points Most recent by Pedro Neves February 2020Community Q&A
• 
  Topology Optimization with Inertia Relief seems off ?!

  Answered Merula_20758 1.6K views 7 comments 0 points Most recent by Rahul Rajan_21763 February 2020Community Q&A
• 
  How to not generate OP2 File

  Answered Bugli 243 views 1 comment 0 points Most recent by QuyNguyenDai February 2020Community Q&A
• 
  FEM Theory Question: Creating a local model from a global model

  Answered Crashphys 558 views 2 comments 0 points Most recent by Crashphys February 2020Community Q&A
• 
  Optistruct doesn't start at all

  Answered Altair Forum User 1.6K views 2 comments 0 points Most recent by Rahul Rajan_21763 February 2020Community Q&A