OptiStruct

Discussion List

• 
  How can i apply 2 differents loads?

  Answered Daniel Lopez 227 views 2 comments 0 points Most recent by Kai Tietz October 2020Community Q&A
• 
  Why Contact pressure is negative?

  Answered Mani kumar_21615 221 views 1 comment 0 points Most recent by FaroukM October 2020Community Q&A
• 
  Question about OS-E 0335

  Answered Mark Lin 239 views 2 comments 0 points Most recent by Mark Lin October 2020Community Q&A
• 
  トポロジー最適化: 拘束反力を使って拘束部への部材を残す例

  altair_fukuoka 953 views 1 comment 1 point Most recent by Danielle_21252 October 2020Altair HyperWorks - 日本語
• 
  Difference between Euler's critical load and Buckling Analysis "F" parameter

  Answered LFSS 294 views 2 comments 0 points Most recent by Adriano Koga_20259 October 2020Community Q&A
• 
  Freesize Composite Optimization - Response mass - understand .out-file

  Answered arh423 91 views 1 comment 0 points Most recent by Adriano Koga_20259 October 2020Community Q&A
• 
  Wear calculation usign FEM

  Answered lucariga 169 views 2 comments 0 points Most recent by Rogerio Nakano_21179 October 2020Community Q&A
• 
  RBE 3 independent nodes forces

  Answered RodrigoFST_22268 949 views 1 comment 0 points Most recent by Rogerio Nakano_21179 October 2020Community Q&A
• 
  Beam contact

  Answered ivanIEV 332 views 2 comments 0 points Most recent by QuyNguyenDai October 2020Community Q&A
• 
  2020 Virtual Altair Student Workshop - Design of a Formula Student Race car: Optimizing major Suspension Components with Altair HyperWorks

  Rahul_P1 51 views 0 comments 0 points Most recent by Rahul_P1 October 2020Altair HyperWorks
• 
  Comparing Simulation Results for Lattice Structure between Simsolid and Tradit

  yuhaohe 111 views 0 comments 0 points Most recent by yuhaohe September 2020Altair HyperWorks
• 
  Model Suspension

  Answered Altair Forum User 615 views 9 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Design var. Pattern Grouping - 3-plane sym

  Answered Pascal_21481 347 views 1 comment 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Self loosening of bolts under trans vibrations

  Answered mpvnaresh 211 views 2 comments 0 points Most recent by mpvnaresh September 2020Community Q&A
• 
  .H3D not generated

  Answered alejandro.saura 249 views 2 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Optimizing standard tube thickness

  Answered Valentin 190 views 2 comments 0 points Most recent by Dhanasharee Jadhav_21915 September 2020Community Q&A
• 
  Critical speed of a shaft

  Answered Daniel Medina 344 views 1 comment 0 points Most recent by Dhanasharee Jadhav_21915 September 2020Community Q&A
• 
  Topology optimization using GRMS stress from Randdom Vibration (PSD) analysis as input

  Answered AbhilashG 268 views 2 comments 0 points Most recent by Dhanasharee Jadhav_21915 September 2020Community Q&A
• 
  Topology optimization using GRMS stress from Randdom Vibration (PSD) analysis as input

  Answered AbhilashG 104 views 1 comment 0 points Most recent by Dhanasharee Jadhav_21915 September 2020Community Q&A
• 
  Static Analysis - Weighted Compliance

  Answered arh423 378 views 6 comments 0 points Most recent by arh423 September 2020Community Q&A
• 
  rbe3 into mpc

  Answered arh423 204 views 4 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Optimizing standard tube thickness

  Answered Valentin 118 views 1 comment 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  internal programming error in contslv_AN.F at location #200

  Answered Altair Forum User 3.5K views 8 comments 0 points Most recent by Altair Forum User September 2020Community Q&A
• 
  Thermal analysis in Optistruct - Gap elements

  Answered Mateusz L 918 views 8 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  "Optistruct & Radioss not installed currently"

  Answered Gokulnath 797 views 1 comment 0 points Most recent by Koushik Chandrashekhar_21806 September 2020Community Q&A
• 
  How to export Lattice optimization results to STL format?

  Answered kjc95 317 views 4 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Composite Free-Size-, Size-, Shuffle-Optimization - Minimize compliance vs. minimize mass

  Answered arh423 199 views 2 comments 0 points Most recent by arh423 September 2020Community Q&A
• 
  Failure for Optistruct

  Answered Altair Forum User 544 views 5 comments 0 points Most recent by Altair Forum User September 2020Community Q&A
• 
  Free-Size optimization

  Answered Mirhan Ozdemir_21843 153 views 2 comments 0 points Most recent by Adriano_Koga September 2020Community Q&A
• 
  Strain-based element failure

  Answered Altair Forum User 1.1K views 4 comments 0 points Most recent by Altair Forum User September 2020Community Q&A