HyperMesh

Tetra Meshing Criteria (Batch Mesh)

Answered Altair Forum User 9.9K views 2 comments 0 points Most recent by Altair Forum User October 2013Community Q&A
ANSYS - Pretension Bolt Utility

Answered Altair Forum User 2.5K views 3 comments 0 points Most recent by Altair Forum User October 2013Community Q&A
create 2D surface mesh from 3D mesh - [face]

Answered Altair Forum User 22.4K views 9 comments 0 points Most recent by Altair Forum User October 2013Community Q&A
Quad meshing of a femur 3-D model

Answered Altair Forum User 3.3K views 11 comments 0 points Most recent by Altair Forum User October 2013Community Q&A
How to create separate mid-surfaces from a assembly

Answered Altair Forum User 2.1K views 2 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Hypermesh 12 (linux) crashes on File/Save after importing geometry

Answered Altair Forum User 3.3K views 2 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
tet10 mesh in LS-Dyna

Answered Altair Forum User 6.4K views 6 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
lsdyna application of hourglass

Answered Altair Forum User 2.4K views 2 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Imprint Bead from Geometry

Answered Altair Forum User 2.3K views 3 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Using Symmetry in Modal Analysis

Answered Altair Forum User 3.8K views 1 comment 0 points Most recent by Altair Forum User September 2013Community Q&A
Solid map, mappable view option

Answered Altair Forum User 5K views 3 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Meshing alone certain Points

Answered Altair Forum User 1.8K views 5 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Slow Loading Model

Answered Altair Forum User 6.4K views 7 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
tcl command: nodes on surfaces of a solid

Answered Altair Forum User 3.6K views 1 comment 0 points Most recent by Altair Forum User September 2013Community Q&A
tcl command for nodes on a surface?

Answered Altair Forum User 1.6K views 2 comments 0 points Most recent by tinh September 2013Community Q&A
Spot weld on very fine mesh

Answered Altair Forum User 3.6K views 2 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Midsurfacing complex geometry

Answered Altair Forum User 2.2K views 3 comments 0 points Most recent by Altair Forum User September 2013Community Q&A
Meshing issues with imported files (Parasolid or iges)

Answered Altair Forum User 1.5K views 2 comments 0 points Most recent by tinh September 2013Community Q&A
Edge smoothing for stamped parts

Answered Altair Forum User 1.2K views 1 comment 0 points Most recent by Altair Forum User September 2013Community Q&A
What is difference between Constraining nodes vs. rbe3?

Answered Altair Forum User 5.6K views 1 comment 0 points Most recent by Altair Forum User August 2013Community Q&A
Apply a mass?

Answered Altair Forum User 6.7K views 3 comments 0 points Most recent by Altair Forum User August 2013Community Q&A
Apply a mass?

Answered Altair Forum User 1.3K views 1 comment 0 points Most recent by Altair Forum User August 2013Community Q&A
lsdyna error 20252

Answered Altair Forum User 4.7K views 5 comments 0 points Most recent by tinh August 2013Community Q&A
How to exclude a part from an analysis

Answered Altair Forum User 2.8K views 4 comments 0 points Most recent by Altair Forum User August 2013Community Q&A
Selection of Corner Nodes

Answered Altair Forum User 1.6K views 2 comments 0 points Most recent by Altair Forum User August 2013Community Q&A
Bolt hole information for Solid Components

Answered Altair Forum User 1.3K views 1 comment 0 points Most recent by Altair Forum User August 2013Community Q&A
Remeshing the whole model?

Answered maysam 9.2K views 4 comments 0 points Most recent by tinh August 2013Community Q&A
hole detection commands

Answered Altair Forum User 2.2K views 1 comment 0 points Most recent by Altair Forum User August 2013Community Q&A
Meshing in General, Guidelines for good meshing

Answered Altair Forum User 3.7K views 3 comments 0 points Most recent by Altair Forum User August 2013Community Q&A
Tetrameshing IGES file.

Answered Altair Forum User 1.4K views 1 comment 0 points Most recent by Altair Forum User August 2013Community Q&A

Upcoming Events

Altair HyperMesh - Introduction to New Interface and Technology Monthly Series
Each of the sessions has the same content and is meant to give an overview over new tools and technologies in HyperMesh as well as a practical introduction to the user interface. Sessions occur every second Thursday of each month from 9 AM to 12 PM CET, including a 15-minute break. Registration is now open for the…
HF Session 13 - Designing Frequency Selective Surfaces (FSS) and modelling Radomes with characterized surfaces in Al
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to design Frequency Selective Surfaces (FSS) in Altair Feko? 2) How to model Radomes with…
HF Session 14 - Performing optimization using Altair Feko & advanced optimization features with Altair Hyperstudy
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to perform optimization using Altair Feko? 2) Advanced optimization using Feko and HyperStudy We will…
HF Session 15 - Overcoming meshing challenges and insight on effective techniques for CAD Cleanup in Altair Feko
In this session, you will learn: 1) How to fix meshing errors in Altair Feko? 2) Tips and tricks on how to clean CAD in Altair Feko We will allow for 10 mins of Q&A after the presentation. This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here:

HyperMesh

Discussion List