English

Discussion List

• 
  Generation of Hexahedral Mesh on complex geometries

  Answered Vaibhav Kulkarni 103 views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  Signal Processing: differences between Compose and HyperGraph

  Roberta Varela_20843 445 views 0 comments 1 point Most recent by Roberta Varela_20843 March 2021Altair HyperWorks
• 
  Compute magnet and rotor losses in a 3D simulation

  Accepted ✓ Ciro Alosa_22608 930 views 17 comments 0 points Most recent by fzidat March 2021Community Q&A
• 
  Abaqus DEFLUX Subroutine Load Step option in Hypermesh

  Answered Uday Pal 360 views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  Electrical Machines: Are results of a drawn segment equal to that of the full machine?

  Answered DWilson7 167 views 3 comments 0 points Most recent by fzidat March 2021Community Q&A
• 
  altair embed's error for the digital twin contest

  Answered MG_20752 260 views 1 comment 0 points Most recent by Rahul_P1 March 2021Community Q&A
• 
  How to reference the Preference file location

  Accepted ✓ Ryan O'Sullivan 244 views 4 comments 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  Is it possible to custom map a set of results by element? Such as element modulus * direct strain?

  Answered Jason Bell 457 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  INCREASING ERROR % PROBLEMS in RADIOSS

  Answered BULA 374 views 3 comments 0 points Most recent by BULA March 2021Community Q&A
• 
  Optistruct Optimization : How to setup an optimization on material ID of components?

  Answered Veronique Bouvette 359 views 1 comment 0 points Most recent by Gildas_GUILLY March 2021Community Q&A
• 
  How to remove these small surfaces (defeatures)?

  Answered Upnishad Kasturi 927 views 2 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  Spurious results in thermal analysis with SimSolid

  Answered Mike_20941 234 views 1 comment 0 points Most recent by Chayan March 2021Community Q&A
• 
  Compressive test with LAW25

  Answered ke li 135 views 1 comment 0 points Most recent by Rogerio Nakano_21179 March 2021Community Q&A
• 
  chang failure in LAW 25

  Answered ke li 279 views 1 comment 0 points Most recent by Rogerio Nakano_21179 March 2021Community Q&A
• 
  How to I generate faces from a set segment

  Answered Akhilesh Katipally 1.7K views 1 comment 0 points Most recent by UD_21543 March 2021Community Q&A
• 
  I cannot run Optistruct,

  Answered Bo_21079 145 views 3 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Parametric frequency sweep in trianglular signal?

  Answered Altair Forum User 386 views 1 comment 0 points Most recent by Altair Forum User March 2021Community Q&A
• 
  Rapidly Improve Your Product's Design Using Altair Inspire with SimSolid Integration

  Blair Haines_21502 34 views 0 comments 0 points Most recent by Blair Haines_21502 March 2021Altair HyperWorks
• 
  HyperWorks & Anaglyph Laminate Tools Integration

  Blair Haines_21502 76 views 0 comments 0 points Most recent by Blair Haines_21502 March 2021Altair HyperWorks
• 
  FEA analysis for the Optimized Design

  Answered Shabbik Shafiulla 409 views 2 comments 0 points Most recent by Shabbik Shafiulla March 2021Community Q&A
• 
  How to output the node numbers of elements in Hypermesh?

  Answered LIMING LI_21655 1.4K views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  Spur Gear Simulation

  Answered Suvansh Mani_22360 334 views 2 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Extract iron loss and flux density data for each element of FE mesh

  Answered MBIASION 597 views 3 comments 0 points Most recent by asoualmi March 2021Community Q&A
• 
  I get the following error during postprocessing(Motion View):ERROR: Failure in parsing "AKISPL(,0,301001)"!............ I think there is some issue in the part where I have taken the force as a csv file and given as input.........I am attaching the m

  Answered Arjun Jakhar 388 views 1 comment 0 points Most recent by Scott_Z_2 March 2021Community Q&A
• 
  velocity VS avg velocity

  Answered Junta_20361 265 views 2 comments 0 points Most recent by MilanRaval March 2021Community Q&A
• 
  ERROR id : 78 in radioss block explicit analysis

  Answered Altair Forum User 6.8K views 16 comments 0 points Most recent by RAMGANESH March 2021Community Q&A
• 
  TCL - Get current value of Loadcol ADD cards

  Accepted ✓ Blake Berk 535 views 2 comments 0 points Most recent by Blake Berk March 2021Community Q&A
• 
  Motion using Markers with Revolut joint

  Answered Mrage 583 views 4 comments 0 points Most recent by Mrage March 2021Community Q&A
• 
  Mesh Around Hole -toggle lines, add/suppress points or something else?

  Accepted ✓ Mesh1 877 views 3 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Why does surface film coefficient (aka heat transfer coefficient) not equal Heat Flux/(Ts-Tref) ?

  Answered Simon Wilkinson 992 views 1 comment 0 points Most recent by acupro March 2021Community Q&A