English

Discussion List

• 
  How to fill gaps between surfaces after making mid-surface operation ?

  Answered AHMET_21209 881 views 1 comment 0 points Most recent by Adriano_Koga March 2022Community Q&A
• 
  Does flux consider coil reactance in the circuit?

  Answered Iñigo Izaguirre 890 views 11 comments 0 points Most recent by SimonGuicheteau March 2022Community Q&A
• 
  How to request CE_FRIC interface TH output? Or: how to request friction energy?

  Answered Ingeniorator 690 views 4 comments 0 points Most recent by Ingeniorator March 2022Community Q&A
• 
  Implementing nonlinear elastic spring element using type13 or type8

  Accepted ✓ Tetsuya 774 views 2 comments 0 points Most recent by PaulAltair March 2022Community Q&A
• 
  Output Data to Excel

  Answered Altair Forum User 7.1K views 6 comments 0 points Most recent by Altair Forum User March 2022Community Q&A
• 
  Fix Job going to H State

  Manoj Soni_20447 260 views 0 comments 0 points Most recent by Manoj Soni_20447 March 2022Altair HPCWorks
• 
  Unable to assign a BC (Boundary Condition) to a particular surface.

  ydigit 75 views 0 comments 1 point Most recent by ydigit March 2022Altair HyperWorks
• 
  Try to make mapable but some part is not mapable. how to done mapable other part some is tell me.

  Answered Ava Mary 499 views 4 comments 0 points Most recent by Ava Mary March 2022Community Q&A
• 
  Finding Inspire tutorial online

  Answered Marie M 339 views 3 comments 0 points Most recent by Marie M March 2022Community Q&A
• 
  PBS Pro Job is Getting Stuck in a Wait (W) state. How Do I Run My Job Now?

  Manoj Soni_20447 158 views 0 comments 0 points Most recent by Manoj Soni_20447 March 2022Altair HPCWorks
• 
  Static Structural Analysis of a bicycle frame (frame.stp)

  Answered Ava Mary 524 views 3 comments 0 points Most recent by Adriano_Koga March 2022Community Q&A
• 
  Any one provide the value of Aluminum /Iron Mat9 G11, G22, G33, G44, G55,G66 and A1, A2, A3 and TREF. I had also cheeck in Altair Hyperwork material book but there is not given.

  Question Ava Mary 362 views 0 comments 0 points Most recent by Ava Mary March 2022Community Q&A
• 
  why CID for CBUSH is turned on to Zero

  Answered VIGNESH_V_25 992 views 2 comments 0 points Most recent by VIGNESH_V_25 March 2022Community Q&A
• 
  SN curve set value for steel material SRI1 ? B1 ? NC1 ? SE ?

  Answered Ava Mary 499 views 1 comment 0 points Most recent by Matthias Goelke_22079 March 2022Community Q&A
• 
  Finding Element by its #

  Accepted ✓ Andreas_21732 1.5K views 1 comment 0 points Most recent by Aniruddha Duggani March 2022Community Q&A
• 
  Fatugue Analysis S-N Method

  Answered Altair Forum User 2.3K views 4 comments 0 points Most recent by Altair Forum User March 2022Community Q&A
• 
  How to Calculate Linearized Stress in SimSolid

  Gouthami Polina_22137 525 views 0 comments 2 points Most recent by Gouthami Polina_22137 March 2022Altair HyperWorks
• 
  Rollout: learning the solution vs the simulation

  Eamon Whalen 760 views 0 comments 2 points Most recent by Eamon Whalen March 2022Other Discussion & Knowledge
• 
  HYPERWORKS imports a model and without changing anything exports with an error for the connecter element property call-out.

  Question James Shavrmnoch 180 views 0 comments 0 points Most recent by James Shavrmnoch March 2022Community Q&A
• 
  Downloading Altair Simulation Products Installer

  Matthieu Pupat 1.4K views 0 comments 1 point Most recent by Matthieu Pupat March 2022Other Discussion & Knowledge
• 
  HyperWorks CFD Known Issues

  Harsh Shah 354 views 0 comments 1 point Most recent by Harsh Shah March 2022Altair HyperWorks
• 
  How do I use Altair virtual wind Tunnel for Ultra FluidX on a windows system. If it is not possible to use it on windows, what is the other alternative ?

  Accepted ✓ Keshav Shukla 811 views 1 comment 0 points Most recent by Adriano_Koga March 2022Community Q&A
• 
  Observing an error message while doing the topological optimization of solid geometry, 'VOLFRAC response on DRESP1 card 1 is not applied to a topology or free-size domain'.

  Answered Saurabh Borse 1.1K views 1 comment 0 points Most recent by Adriano_Koga March 2022Community Q&A
• 
  Multilayer Antenna - Faces View

  Answered Sem z 487 views 1 comment 0 points Most recent by Mel March 2022Community Q&A
• 
  Direct Transient Response Analysis of a Spanner?

  Answered Ava Mary 556 views 3 comments 0 points Most recent by wscott March 2022Community Q&A
• 
  Hyperview - while using multi window and 2 or more result files

  Question Electrification 319 views 0 comments 0 points Most recent by Electrification March 2022Community Q&A
• 
  Particles penetrating the geometry

  Accepted ✓ Ahmed Rami 761 views 2 comments 0 points Most recent by Ahmed Rami March 2022Community Q&A
• 
  Workspace File Corrupt

  Answered Frank_21738 339 views 4 comments 0 points Most recent by Frank_21738 March 2022Community Q&A
• 
  What have I done wrong with shuffle optimization, why the core ply change the position, actually it should not be stacked?

  Accepted ✓ Paphatsorn 507 views 4 comments 0 points Most recent by Paphatsorn March 2022Community Q&A
• 
  I have downloaded the student licence, OptiStruct doesn't work.

  Answered Kristian Flores 499 views 2 comments 0 points Most recent by Kristian Flores March 2022Community Q&A