OptiStruct

sol 101 MD-Nastran

Answered Altair Forum User 716 views 1 comment 0 points Most recent by Altair Forum User October 2017Community Q&A
Application of MBDEACT

Answered Altair Forum User 424 views 1 comment 0 points Most recent by Altair Forum User October 2017Community Q&A
element edges

Answered Altair Forum User 1.3K views 2 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Can 2 rigids have the same dependent nodes?

Answered RodrigoFST_22268 977 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
Modal Frequency optimization

Answered Punith 2.7K views 11 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
output block optistruct

Answered Altair Forum User 1.6K views 6 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Error calling MATLAB engine in external library (error 6400)

Answered Altair Forum User 1.3K views 6 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Work Hardening slope

Answered Karthic_22061 1.4K views 2 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
"Skin" results output for solid elements

Answered timonq 2.4K views 8 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Total Deflection in Fatigue Analysis

Answered Suresh J 686 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
Change TIE to other connection

Answered timonq 1.1K views 4 comments 0 points Most recent by timonq September 2017Community Q&A
impact hammer modal test

Answered durukanbdilek 853 views 3 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
transient response analysis of gang bridge

Answered Altair Forum User 1.2K views 12 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Problem with import of 2D shell and 3D hexa elements with OSSmooth

Answered Altair Forum User 1.1K views 7 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Delete option inside Hyperview / File size reduction

Answered Altair Forum User 959 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
How to set up a model including superelement in Hypermesh (nastran) for constrained modal analysis

Answered Altair Forum User 2.8K views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
optimization run time

Answered Altair Forum User 1.2K views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
GRAV, ACCELERATION Model

Answered Udhay Rohith 2.8K views 10 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Shuffle optimization

Answered Altair Forum User 854 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
four-point bending test

Answered Altair Forum User 1.1K views 7 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
MATX33_FOAM

Answered Altair Forum User 510 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
Mat card for concrete beam

Answered Altair Forum User 541 views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
Import file problem

Answered Altair Forum User 2.5K views 5 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Wrong results with negative compliance

Answered Altair Forum User 2.2K views 2 comments 0 points Most recent by Rahul Rajan_21763 September 2017Community Q&A
simulation does not start - error output file

Answered Altair Forum User 1.3K views 2 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Technical difference between thickness direction gasket pressure distribution and contact pressure distribution on gasket

Answered pratik gadve 1.4K views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
PARAM, COUPMASS & WTMASS

Answered Karthic_22061 2.6K views 1 comment 0 points Most recent by Altair Forum User September 2017Community Q&A
mass OPtimisation by changing square size and thickness

Answered Altair Forum User 1.9K views 16 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
Dynamic analysis of a Component

Answered Altair Forum User 1.9K views 4 comments 0 points Most recent by Altair Forum User September 2017Community Q&A
topology optimization

Answered Altair Forum User 1.3K views 1 comment 0 points Most recent by Rahul Rajan_21763 September 2017Community Q&A

Upcoming Events

Altair HyperMesh - Introduction to New Interface and Technology Monthly Series
Each of the sessions has the same content and is meant to give an overview over new tools and technologies in HyperMesh as well as a practical introduction to the user interface. Sessions occur every second Thursday of each month from 9 AM to 12 PM CET, including a 15-minute break. Registration is now open for the…
HF Session 13 - Designing Frequency Selective Surfaces (FSS) and modelling Radomes with characterized surfaces in Al
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to design Frequency Selective Surfaces (FSS) in Altair Feko? 2) How to model Radomes with…
HF Session 14 - Performing optimization using Altair Feko & advanced optimization features with Altair Hyperstudy
This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here: Note: This webinar is part of the Community Magnetics Chat series. In this session, you will learn: 1) How to perform optimization using Altair Feko? 2) Advanced optimization using Feko and HyperStudy We will…
HF Session 15 - Overcoming meshing challenges and insight on effective techniques for CAD Cleanup in Altair Feko
In this session, you will learn: 1) How to fix meshing errors in Altair Feko? 2) Tips and tricks on how to clean CAD in Altair Feko We will allow for 10 mins of Q&A after the presentation. This event is part of the Community Magnetics Fireside Chat series. Previous webinar recordings can be found here:

OptiStruct

Discussion List