HyperMesh

Discussion List

• 
  detect unconnected elements in single collector, bolt preload, scripting

  Answered Sagar Desai 349 views 2 comments 0 points Most recent by Sagar Desai March 2021Community Q&A
• 
  How can I know the values of Fatigue strength coefficient, Fatigue strength exponent, Nc1, FL and SE in Optistruct fatigue analysis? And how to decide value of N in FATSEQ card?

  Answered Jay Thakkar 1.2K views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Altair HyperWorks™: Material Library

  Uli Gollwitzer_21720 1.3K views 0 comments 1 point Most recent by Uli Gollwitzer_21720 March 2021Altair HyperWorks
• 
  Altair HyperWorks™: Take Full Advantage of Latest Model Browser Functionalities

  Uli Gollwitzer_21720 494 views 0 comments 0 points Most recent by Uli Gollwitzer_21720 March 2021Altair HyperWorks
• 
  Bug in Views Display Modes

  Answered Michel Del Risco 193 views 1 comment 1 point Most recent by Vdal89 March 2021Community Q&A
• 
  How to create two node sets on a same plane of a cylinder using tcl

  Accepted ✓ Ash Ahamed 925 views 5 comments 0 points Most recent by Hypermesh User March 2021Community Q&A
• 
  エクスポート時のコメント

  Accepted ✓ YuzuN 327 views 2 comments 0 points Most recent by Imoto March 2021質問と回答 (Q&A)
• 
  Generation of Hexahedral Mesh on complex geometries

  Answered Vaibhav Kulkarni 103 views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  Abaqus DEFLUX Subroutine Load Step option in Hypermesh

  Answered Uday Pal 350 views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  How to reference the Preference file location

  Accepted ✓ Ryan O'Sullivan 226 views 4 comments 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  How to remove these small surfaces (defeatures)?

  Answered Upnishad Kasturi 917 views 2 comments 0 points Most recent by Viraj_Kulkarni March 2021Community Q&A
• 
  How to I generate faces from a set segment

  Answered Akhilesh Katipally 1.7K views 1 comment 0 points Most recent by UD_21543 March 2021Community Q&A
• 
  HyperWorks & Anaglyph Laminate Tools Integration

  Blair Haines_21502 76 views 0 comments 0 points Most recent by Blair Haines_21502 March 2021Altair HyperWorks
• 
  FEA analysis for the Optimized Design

  Answered Shabbik Shafiulla 385 views 2 comments 0 points Most recent by Shabbik Shafiulla March 2021Community Q&A
• 
  How to output the node numbers of elements in Hypermesh?

  Answered LIMING LI_21655 1.4K views 1 comment 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  TCL - Get current value of Loadcol ADD cards

  Accepted ✓ Blake Berk 507 views 2 comments 0 points Most recent by Blake Berk March 2021Community Q&A
• 
  Mesh Around Hole -toggle lines, add/suppress points or something else?

  Accepted ✓ Mesh1 857 views 3 comments 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Tsai failure criterion

  Accepted ✓ Fernando Hernández Alonso_20813 1.1K views 4 comments 0 points Most recent by Wesley Castro_21290 March 2021Community Q&A
• 
  Applying loads/constraints to sets

  Accepted ✓ Fernando Hernández Alonso_20813 749 views 2 comments 0 points Most recent by Fernando Hernández Alonso_20813 March 2021Community Q&A
• 
  linear temperature as a load on nodes

  Answered Altair Forum User 5.3K views 5 comments 0 points Most recent by Akshay Deshmukh March 2021Community Q&A
• 
  How to extract E-Module Point Map

  Answered Lukas Fischer_22504 243 views 3 comments 0 points Most recent by Wesley Castro_21290 March 2021Community Q&A
• 
  How to mask elements by box using tcl

  Accepted ✓ Ash Ahamed 828 views 2 comments 0 points Most recent by Gabriel_Justo March 2021Community Q&A
• 
  Meshing recommendations for elements reaching zero or negative volume during simulation

  Answered Ingeniorator 761 views 2 comments 0 points Most recent by Ingeniorator March 2021Community Q&A
• 
  How to migrate HM shared library to a new server

  pravarth 53 views 0 comments 1 point Most recent by pravarth March 2021Altair HyperWorks
• 
  How to join these nodes and form a surface

  Answered Upnishad Kasturi 273 views 2 comments 0 points Most recent by QuyNguyenDai March 2021Community Q&A
• 
  FAQ 15 Mesh Checks 7. How to retrieve the failed elements from check elems panel

  Answered Rahul_P1 5.2K views 2 comments 0 points Most recent by Hyunsok Pang March 2021Community Q&A
• 
  Integrating Altair Compose and other Altair applications

  Roberta Varela_20843 233 views 0 comments 3 points Most recent by Roberta Varela_20843 March 2021Altair HyperWorks
• 
  How can I calculate the average fieldl value of a section?

  Answered Leire Furundarena 550 views 3 comments 0 points Most recent by acupro March 2021Community Q&A
• 
  Is there a way to detach more than two nodes at a time?

  Answered Daniel Wang 661 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A
• 
  Actual Min of a curve

  Answered Dariush Tari 89 views 1 comment 0 points Most recent by Adriano Koga_20259 March 2021Community Q&A