English

Discussion List

• 
  Failed to read hstp file

  Answered david green 412 views 3 comments 0 points Most recent by david green December 2023Community Q&A
• 
  How to project node on free edge of element ?

  Answered Bhavik Sheth_21143 236 views 1 comment 0 points Most recent by Fred_Juras December 2023Community Q&A
• 
  How do you utilise your computer to reduce Run Time?

  Answered Alice Daniels 360 views 2 comments 0 points Most recent by Wesley_Peijnenburg2 December 2023Community Q&A
• 
  Results vary between different versions of compilation and execution.

  Accepted ✓ Jeff_wu 217 views 1 comment 0 points Most recent by pdarnell December 2023Community Q&A
• 
  I am trying to design a closed loop synchronous boost converter with the following specification with the help of C command block

  Answered Altair Forum User 657 views 3 comments 0 points Most recent by mohamad shahbazi December 2023Community Q&A
• 
  save only a part of time integration

  Accepted ✓ Luca Cavagna 277 views 4 comments 1 point Most recent by GTT Adam December 2023Community Q&A
• 
  Contour Min/Max for Sets, Components, displayed entities

  Sebastian_Karp 337 views 0 comments 0 points Most recent by Sebastian_Karp December 2023Altair Exchange
• 
  License error

  Answered Kiran Purushothama Keshavan 472 views 3 comments 0 points Most recent by Eric_Veikle December 2023Community Q&A
• 
  Extract section cut data

  Michael Herve 262 views 0 comments 0 points Most recent by Michael Herve December 2023Altair Exchange
• 
  How to Obtain S parameters from far field source?

  Answered Juan Felipe Caicedo 253 views 1 comment 0 points Most recent by Shannon_Mistry December 2023Community Q&A
• 
  Acusolve heat and mass transfer models

  Accepted ✓ Yangyang_Shen 371 views 1 comment 0 points Most recent by jerrinjobs December 2023Community Q&A
• 
  How to convert Yaw / Pitch / Roll angles to use them as input for rotational DOFs 4 5 6

  Answered IngeniosIT 466 views 1 comment 0 points Most recent by GTT Adam December 2023Community Q&A
• 
  Error for EDEM-FLUENT coupling

  Accepted ✓ Yang_QI1 330 views 1 comment 0 points Most recent by Stephen Cole December 2023Community Q&A
• 
  Altair Student Edition Limitations Of Nodes

  Answered Nam Tran Dai 746 views 1 comment 0 points Most recent by Michael Herve December 2023Community Q&A
• 
  Can I create a non-meshed coil from an existing volume?

  Answered Will_20672 386 views 1 comment 0 points Most recent by Letizia Ferrara December 2023Community Q&A
• 
  Get force information from previous model

  Accepted ✓ Yang_QI1 213 views 1 comment 0 points Most recent by RWood December 2023Community Q&A
• 
  how to get screen position of user click ?

  Answered Bhavik Sheth_21143 347 views 5 comments 0 points Most recent by Bhavik Sheth_21143 December 2023Community Q&A
• 
  Sub model vs full model

  Accepted ✓ Casper Kruger 1.5K views 8 comments 0 points Most recent by Casper Kruger December 2023Community Q&A
• 
  Extraction of a the mass and write in a cell of a table page by tcl

  Answered FaForno 193 views 2 comments 0 points Most recent by Michael Herve December 2023Community Q&A
• 
  FEKO: Is there a way to add a solution request to a large problem without solving the matrix again?

  Answered Maruf Hossain_21119 185 views 3 comments 0 points Most recent by Maruf Hossain_21119 December 2023Community Q&A
• 
  Want to know relevance of "** ERROR RETURN ** FROM CMUMPS INFO(1)= -1 ** INFO(2)= 22"

  Answered Michael R 225 views 4 comments 0 points Most recent by Torben Voigt December 2023Community Q&A
• 
  Find edge nodes of meshes and create node sets

  Sebastian_Karp 203 views 0 comments 0 points Most recent by Sebastian_Karp December 2023Altair Exchange
• 
  Export solver deck for all simulation steps

  Sebastian_Karp 223 views 0 comments 1 point Most recent by Sebastian_Karp December 2023Altair Exchange
• 
  HOW TO GENERATE 2D HEAT-MAP IN FLUX FOR CORELESS AXIAL FLUX MOTOR DESIGN?

  Answered Ishaqlad89 371 views 1 comment 0 points Most recent by Letizia Ferrara December 2023Community Q&A
• 
  Minimum Reinforcement

  Answered Hadi Kugshia 264 views 1 comment 0 points Most recent by Andres Chavez December 2023Community Q&A
• 
  Error in the DLL block. script error at time step 0.00005

  Question mohamad shahbazi 310 views 0 comments 0 points Most recent by mohamad shahbazi December 2023Community Q&A
• 
  Why am I getting an error related to an inconsistent version of Hyperworks CFD and AcuSolve version?

  Answered Rubén Barrio Pérez 357 views 7 comments 0 points Most recent by Rubén Barrio Pérez December 2023Community Q&A
• 
  ERROR :No RUN command found // Hyperworks CFD 2022.3

  Answered Chrysi_P 243 views 6 comments 0 points Most recent by Chrysi_P December 2023Community Q&A
• 
  Acusolve post processing in Abaqus

  Accepted ✓ Rafal Blasczykowski 421 views 6 comments 0 points Most recent by acupro December 2023Community Q&A
• 
  Identify the top layer particles in a rotary kiln

  Answered Yangyang_Shen 283 views 1 comment 0 points Most recent by RWood December 2023Community Q&A