OptiStruct

Discussion List

• 
  How to analyze model after multi material topology optimization

  Question Keita 323 views 0 comments 0 points Most recent by Keita November 2021Community Q&A
• 
  Pre-tension note

  Question Casper Kruger 364 views 0 comments 0 points Most recent by Casper Kruger November 2021Community Q&A
• 
  1d Beam element Optistruct

  Answered Tsherig 98 views 1 comment 0 points Most recent by Rogerio Nakano_21179 November 2021Community Q&A
• 
  【NVH】CMSとCDSの組合せによる固有値パラメータスタディの超高速化

  Sonoda 353 views 0 comments 1 point Most recent by Sonoda November 2021Altair HyperWorks - 日本語
• 
  AcuSolve : 流体構造連成（DC-FSI）チュートリアル「ACU-T:5403」

  Masu 278 views 0 comments 0 points Most recent by Masu November 2021Altair HyperWorks - 日本語
• 
  How to write an equation of gasket pressure variance for topology optimization response？

  Question Travis_20917 188 views 0 comments 0 points Most recent by Travis_20917 November 2021Community Q&A
• 
  How do I get elemental strain energy output for all elements (2D and 3D as well)?

  Answered Rachit Semalty 399 views 2 comments 0 points Most recent by Rachit Semalty November 2021Community Q&A
• 
  Can some one help me with the optimization of pin fins. I have a 2D plate and I am unable to apply heat flux to the selected elements.

  Question Vishnu Ganesan 220 views 0 comments 0 points Most recent by Vishnu Ganesan November 2021Community Q&A
• 
  Optistruct - AWS cost optimization study

  pravarth 196 views 0 comments 3 points Most recent by pravarth November 2021Altair HyperWorks
• 
  Label STRESS is missing on FATPARM card.

  Answered Abdul Muizz Jamal 375 views 3 comments 0 points Most recent by Abdul Muizz Jamal November 2021Community Q&A
• 
  Is there any way to get bending wave speed through Optistruct or any other Altair product?

  Question Sanit Bhatkar_21192 833 views 0 comments 0 points Most recent by Sanit Bhatkar_21192 November 2021Community Q&A
• 
  How do I get elemental strain energy output for all elements (2D and 3D as well)?

  Answered Rachit Semalty 1.5K views 2 comments 0 points Most recent by Rachit Semalty November 2021Community Q&A
• 
  Optistruct not installed

  Answered Lena Smole 377 views 2 comments 0 points Most recent by Lena Smole November 2021Community Q&A
• 
  When performing a composite (laminate) optimization, I Cannot see in the sizing80.fem the set related to the superply even tough I set the FZSTOSZ option in the output. How can I fix this issue?

  Question 1234 145 views 0 comments 0 points Most recent by 1234 November 2021Community Q&A
• 
  Sequencial analysis in NLtrans

  Answered Vidyaprakash G S 297 views 1 comment 0 points Most recent by Gildas_GUILLY November 2021Community Q&A
• 
  How do i know which MAT in optistruct to define my material property?

  Accepted ✓ Paphatsorn 476 views 4 comments 0 points Most recent by Paphatsorn November 2021Community Q&A
• 
  How to avoid generating free parts (separate parts) in topology optimization?

  Answered WEIKANG SONG 377 views 1 comment 0 points Most recent by Gildas_GUILLY November 2021Community Q&A
• 
  ERROR 14: Missing DESVAR # 1 referenced by DRESP3 # 2.

  Answered Anatole Morcos 766 views 2 comments 0 points Most recent by Anatole Morcos November 2021Community Q&A
• 
  DRESP3 - how to get the center of mesh element and how to use DESVAR ?

  Answered Anatole Morcos 202 views 1 comment 0 points Most recent by Ben Buchanan November 2021Community Q&A
• 
  romAI: How to speed-up DEM simulations leveraging Artificial Intelligence

  Spiros_Mallios 6.9K views 0 comments 5 points Most recent by Spiros_Mallios November 2021Other Discussion & Knowledge
• 
  Parts and Instances functionality in Optistruct

  Naren 233 views 0 comments 1 point Most recent by Naren October 2021Altair HyperWorks
• 
  Model runs for analysis but not for optimization

  Answered Stéphane C. 267 views 2 comments 0 points Most recent by RobHoglund October 2021Community Q&A
• 
  Ground Simulation and Contact Problems

  Answered Nayara Lacerda 254 views 2 comments 0 points Most recent by Adriano_Koga October 2021Community Q&A
• 
  Transient thermal linear analysis - Choosing right values for PCONV group

  Answered Agasttya Dixit 390 views 1 comment 0 points Most recent by Adriano_Koga October 2021Community Q&A
• 
  Hyperworks – Introduction of Load Step Inputs card collector for Optistruct user profile

  Alberto Campagna 345 views 0 comments 2 points Most recent by Alberto Campagna October 2021Altair HyperWorks
• 
  Modeling Virtual Fluid Mass in OptiStruct with MFLUID

  RobHoglund 3.1K views 0 comments 1 point Most recent by RobHoglund October 2021Altair HyperWorks
• 
  How to divide an Optistruct run on multiple scratch disks.

  FredrikI_21476 67 views 0 comments 0 points Most recent by FredrikI_21476 October 2021Altair HyperWorks
• 
  Shape Controls - Symmetric Plans does reduce my solution time when inserted on the model? - Topology Optimization

  Answered Diogo Vicente_21694 287 views 1 comment 0 points Most recent by RobHoglund October 2021Community Q&A
• 
  Risks of Using CBAR Elements | Just use CBEAM Elements Instead

  BenB_22580 1.1K views 0 comments 1 point Most recent by BenB_22580 October 2021Altair HyperWorks
• 
  3 Step Composite Optimization Cheat Sheet: Shape, Size, Shuffle

  Lacie 2.2K views 0 comments 2 points Most recent by Lacie October 2021Altair HyperWorks