Altair RISE

A program to recognize and reward our most engaged community members

Nominate Yourself Now!

Why don't I see my model in Hyperview

Hi,

It is the first time that I am using the Hyperworks X (the new interface of Hyperworks). I ran Optistruct and it worked (as you can see in the figure below). The problem is when I click on 'Results', it opens in Hyperview, but there is nothing, I can't see my model (as you can see in the last picture).

Thank you

Anne

Find more posts tagged with

English

HyperMesh

HyperView

OptiStruct

v2022.1

Accepted answers

All comments

Chayan

Can you check your out file to see if there are any warning messages or errors? Also can you fit your model to the screen, in case it moved off it.

I have seen this happen when the model is nor well constrained, but from your image, it looks like you have constraints on there.

Anne Blouin

I tried to move it to see it, but I am sure it's not there I tried to un zoom a lot and move it. I don't see any error in my out file, but here it is:

*** OptiStruct defaults set from:
install config file: C:/Users/b0648278/Documents/hwsolvers/optistruct.cfg.


NOTE # 9199
MSGLMT=STRICT is active, all messages will be printed unless there is
a subsequent MSGLMT definition to limit error or warning messages.
You can also suppress some less important warning messages by use of
MSGLMT=BRIEF or UNREF (in config file or in the input data).

NOTE # 1929
Created RAM scratch area: total size 30 MB.

************************************************************************

FINITE ELEMENT MODEL DATA INFORMATION :
---------------------------------------

Total # of Grids (Structural) : 204
Total # of Elements : 815
Total # of Degrees of Freedom : 582
(Structural)
Total # of Non-zero Stiffness Terms : 9066

Element Type Information
------------------------

CTETRA Elements : 815

Load and Boundary Information
-----------------------------

LOAD and TEMP Sets: 1
SPC Sets : 1

Material and Property Information
---------------------------------

PSOLID Cards : 1
MAT1 Cards : 1

************************************************************************

OPTIMIZATION PROBLEM PARAMETERS :
---------------------------------

NO DESIGN MATERIAL OR DESIGN VARIABLES FOUND : ANALYSIS ONLY

------------------------
Static Subcase Summary :
------------------------

---------- -------- ------- ---------------------
Subcase ID SPC ID LOAD ID Preloading Subcase ID
---------- -------- ------- ---------------------
1 2 3
---------- -------- ------- ---------------------

Run Type : Analysis Only
Run at location : C:/Users/b0648278/Documents/HyperWork Files/
Scratch file directory : C:/Users/b0648278/Documents/HyperWork Files/
Free space: 349.993 GB
Number of CPU processors : 1

************************************************************************

MEMORY ESTIMATION INFORMATION :
-------------------------------

Solver Type is: Sparse-Matrix Solver
Direct Method

Static Memory (RAM) Allocated in Preprocessor : 800 MB
In addition a ramdisk area was allocated in memory : 30 MB
MUMPS Solver will Run In-Core with Estimated Memory : 1 MB
Estimated Total Memory (RAM) : 831 MB

Estimated Memory (RAM) for Out-of-Core Solution : 4 MB
Estimated Memory (RAM) for In-Core Solution : 4 MB

DISK SPACE ESTIMATION INFORMATION :
-----------------------------------

Estimated Disk Space for Output Data Files : 6 MB
Estimated Scratch Disk Space for In-Core Solution : 0 MB
Estimated Scratch Disk Space for Out-of-Core Solution : 0 MB

************************************************************************

BEGINNING ANALYSIS SOLUTION ....

************************************************************************

ANALYSIS RESULTS :
------------------

ITERATION 0

(Scratch disk space usage for starting iteration = 0 MB)
(Running in-core solution)

Volume = 1.20000E+02 Mass = 0.00000E+00
-----------------------------------
Subcase Compliance Epsilon
-----------------------------------
1 4.520697E+01 1.616581E-11
-----------------------------------

Note : Epsilon = Residual Strain Energy Ratio.

************************************************************************

ANALYSIS COMPLETED.

************************************************************************

RESOURCE USAGE INFORMATION
--------------------------

MAXIMUM MEMORY USED 801 MB
INCLUDING MEMORY FOR MUMPS 1 MB
IN ADDITION 1 MB MEMORY WAS ALLOCATED FOR TEMPORARY USE
IN ADDITION 30 MB RAMDISK AREA WAS ALLOCATED IN MEMORY
MAXIMUM DISK SPACE USED 1 MB
INCLUDING DISK SPACE FOR MUMPS 0 MB

************************************************************************

***** END OF REPORT *****

Chayan

I built and ran a similar model on my end, and looks like it ran without any issues. Did you try loading reading the h3d results file into HyperView?

Community-Pasted-Attachment-1676409223282.png

AM_20700

Can you share your .h3d results file?