OptiStruct

Discussion List

• 
  What to do after obtaining results of topology optimization

  Answered Altair Forum User 697 views 5 comments 0 points Most recent by Altair Forum User May 2018Community Q&A
• 
  How to separate stress result in non-linear quasi-static?

  Answered Altair Forum User 483 views 3 comments 0 points Most recent by tinh May 2018Community Q&A
• 
  CTRIA3 ERROR LINEAR STATIC ANALYSIS

  Answered Altair Forum User 1.9K views 3 comments 0 points Most recent by Altair Forum User May 2018Community Q&A
• 
  compliance error 312 - due to constraints?!?

  Answered Altair Forum User 584 views 7 comments 0 points Most recent by Altair Forum User May 2018Community Q&A
• 
  missing property

  Answered Altair Forum User 1.6K views 2 comments 0 points Most recent by Sanjay Nainani_20973 May 2018Community Q&A
• 
  quality check

  Answered Altair Forum User 819 views 2 comments 0 points Most recent by Sanjay Nainani_20973 May 2018Community Q&A
• 
  help with *** ERROR # 1000 ***

  Answered Altair Forum User 942 views 2 comments 0 points Most recent by Altair Forum User May 2018Community Q&A
• 
  Which plies where after sizing optimization

  Answered Altair Forum User 470 views 2 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Non design space cone

  Answered Altair Forum User 2.6K views 40 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  スーパーエレメントを使用するメリット

  Question AltairTY 1.8K views 0 comments 0 points Most recent by AltairTY April 2018質問と回答 (Q&A)
• 
  最適化計算が終了したときに確認すること

  Question AltairTY 1.2K views 0 comments 0 points Most recent by AltairTY April 2018質問と回答 (Q&A)
• 
  Strain-cycles (EN) Fatigue analysis

  Answered Altair Forum User 601 views 4 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Modelling Frequency Response Impulse Hammer Test

  Answered Altair Forum User 674 views 2 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  von mises stress in lattice opti.

  Answered Aslan_20882 821 views 6 comments 0 points Most recent by Aslan_20882 April 2018Community Q&A
• 
  How to clean up topology optimization result?

  Answered Altair Forum User 2.9K views 6 comments 0 points Most recent by QuyNguyenDai April 2018Community Q&A
• 
  Optistruct model

  Answered Altair Forum User 1.5K views 8 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  OptiiStruct Solver won't work. (Simple compression Test)

  Answered Keonkim1991 4K views 12 comments 0 points Most recent by Keonkim1991 April 2018Community Q&A
• 
  Damage zones in Fail Safe Optimization

  Answered Altair Forum User 918 views 14 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  CNTNLSUB

  Answered Karthic_22061 1.9K views 6 comments 0 points Most recent by Karthic_22061 April 2018Community Q&A
• 
  Thermal BCs

  Answered Altair Forum User 821 views 3 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Modal effectctive Mass

  Answered Altair Forum User 5.2K views 23 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Error #312

  Answered Altair Forum User 1.5K views 9 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Optistruct Optimization creates 1000 plies

  Answered Altair Forum User 635 views 4 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  SPCF on SPC applied to surface

  Answered Jebunderscore 1.2K views 3 comments 0 points Most recent by Jebunderscore April 2018Community Q&A
• 
  No results

  Answered Altair Forum User 532 views 2 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  PRETENSION ANALYSIS

  Answered Jebunderscore 897 views 2 comments 0 points Most recent by Jebunderscore April 2018Community Q&A
• 
  How to set dt with curve?

  Answered Altair Forum User 1.4K views 20 comments 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Imperfection

  Answered Altair Forum User 476 views 1 comment 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  Mapping results of another simulation in hypermesh/optistruct

  Answered Altair Forum User 1.3K views 1 comment 0 points Most recent by Altair Forum User April 2018Community Q&A
• 
  ERROR 4002 - ISTOP = 0

  Answered Altair Forum User 816 views 9 comments 0 points Most recent by Altair Forum User April 2018Community Q&A