OCRI04 => Retrieval of INTEGER attribute aborted

Diogo Cardoso
Diogo Cardoso New Altair Community Member
edited July 2021 in Community Q&A

Hello all,

Im working on a transformer at flux2D 12.2 and a warning appeared and i dont know how to solve it.

 

image

Besides, sometimes other warning apears. And that error is about the convergence about the newton rapson is not achieved. I've been asked for myself if its bad for my results.


Thank you & regards.

Tagged:

Answers

  • asoualmi
    asoualmi
    Altair Employee
    edited June 2021

    Hi,

    how did the error message get?

    have you tried with the new version of Flux?

    Best regards.

  • Diogo Cardoso
    Diogo Cardoso New Altair Community Member
    edited June 2021
    Abdessamed said:

    Hi,

    how did the error message get?

    have you tried with the new version of Flux?

    Best regards.

    Hi,

    The message apears when i was solving the file. After solving that message apears.

    Im simulating a transformer, based on a eletric circuit described on a tutorial of flux, of a old version. I attached that tutorial on this message.

    I've been used the flux2D 12.2 because my university had license for only that version, not to a younger one.

    Best regards.

    The whole warning is:

    OCRI04 => Number RB.F3D.BOBINE_FIL_FIN(0) out of bounds
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Number RB.F3D.BOBINE_FIL_FIN(0) out of bounds
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...

  • asoualmi
    asoualmi
    Altair Employee
    edited June 2021
    Diogo Cardoso said:

    Hi,

    The message apears when i was solving the file. After solving that message apears.

    Im simulating a transformer, based on a eletric circuit described on a tutorial of flux, of a old version. I attached that tutorial on this message.

    I've been used the flux2D 12.2 because my university had license for only that version, not to a younger one.

    Best regards.

    The whole warning is:

    OCRI04 => Number RB.F3D.BOBINE_FIL_FIN(0) out of bounds
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Number RB.F3D.BOBINE_FIL_FIN(0) out of bounds
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...
    OCRI04 => Retrieval of INTEGER attribute aborted
    ICR_IACT => failed
    ICRCO2 => Failed
    PU_CINDUC => failed
    CACCCL => failed...
    CACVAL => failed...

    Send us the Flux project.

    Best regards.

  • Diogo Cardoso
    Diogo Cardoso New Altair Community Member
    edited June 2021
    Abdessamed said:

    Send us the Flux project.

    Best regards.

    Hi,

    Basically you just need to solve the project, with the scenario= Referencevalues, and you will see the warning after that. Another thing I noticed is that Newton's iterations don´t get to 100 as supposed.

    I attached the projetc in this message.

    Thank you for all the suport,
    Best Regards

  • asoualmi
    asoualmi
    Altair Employee
    edited June 2021
    Diogo Cardoso said:

    Hi,

    Basically you just need to solve the project, with the scenario= Referencevalues, and you will see the warning after that. Another thing I noticed is that Newton's iterations don´t get to 100 as supposed.

    I attached the projetc in this message.

    Thank you for all the suport,
    Best Regards

    Hi,

    Thanks for the file. Can you try to delete the senosrs and create it again.

    Once this is done solve the porejct and see if you still get the same error message.

    Best regards.

  • Diogo Cardoso
    Diogo Cardoso New Altair Community Member
    edited July 2021
    Abdessamed said:

    Hi,

    Thanks for the file. Can you try to delete the senosrs and create it again.

    Once this is done solve the porejct and see if you still get the same error message.

    Best regards.

    Hi, 

    I deleted the sensors, i arent using them but when i deleted them, the warning didnt appear again.
    Im just asking myself if the iteration of the newton raphson method is important, because the solving process stoped at number 4 of the iteration, and didnt achieved the number 100. By default are 100 iterations in the method.

    Is that important for the results?

    Thanks for helping me with the warning, at least the warning didnt appear again.

    Best regards.

  • asoualmi
    asoualmi
    Altair Employee
    edited July 2021
    Diogo Cardoso said:

    Hi, 

    I deleted the sensors, i arent using them but when i deleted them, the warning didnt appear again.
    Im just asking myself if the iteration of the newton raphson method is important, because the solving process stoped at number 4 of the iteration, and didnt achieved the number 100. By default are 100 iterations in the method.

    Is that important for the results?

    Thanks for helping me with the warning, at least the warning didnt appear again.

    Best regards.

    For the NR iteration you don't need to do 100 iteration if the convergence reached before.

    Best regards;

Categories