*** ERROR # 1000 *** in the input data: Incorrect data in field # 3
Answers
-
I don't have all the material properties to fill in the properties on the MAT9ORT or Mat9 card so i chose to do MAT8 car instead, should i just assume that the values in 1-2 direction is equal?
Thanks, Neel
0 -
0
-
Hi I changed the material o MAT9ORT and i receive this error I don't understand what I am doing wrong?
Messages for the job:
*** See next message about line 22774 from file:
C:/Users/neel_/OneDrive/Documents/Dissertation/2d model/honeycomb/alhoneycomb3d.fem
'CQUAD4 16667 0 39 21725 228 40'
*** ERROR # 1000 *** in the input data:
Incorrect data in field # 3.
****************
Too many error messages. Aborting run.
Current limit is 10000. Use 'MSGLMT' control card to change this value.
Neel
0 -
Hi @neelc14
Use MaT9ORT only for solid elements. Looks like you changed material and properties for all elements.
0 -
Hi, I only changed the card image for aluminium honeycomb to mat9ort and nothing else but it seems to come up with that error still?
I have attached the file for reference.
Neel
0 -
Hi Neel,
For core you have PSHELL property which is not compatible with solid elements.
Change PSHELL to PSOLID property for core component.
0 -
Hi Prayesh,
Sorry but I already tried that and got an error message again after I ran optistruct analysis.
Messages for the job:
*** See next message about line 22774 from file:
C:/Users/neel_/OneDrive/Documents/Dissertation/2d model/honeycomb/alhoneycomb3d.fem
'CQUAD4 16667 0 39 21725 228 40'
*** ERROR # 1000 *** in the input data:
Incorrect data in field # 3.
****************
Too many error messages. Aborting run.
Current limit is 10000. Use 'MSGLMT' control card to change this value.
Neel
0 -
Neel,
Try this attached .fem file.
Some of the elements did not had a valid property. I updated the model.
0 -
Hi Prayesh could you send me the model file as well please if possible?
Neel
0 -
Hi Prayesh,
I imported the FEM file into Hyperworks and I still receive an error when I try to do Optistruct analysis.
Messages for the job:
*** See next message about line 23157 from file:
C:/Users/neel_/OneDrive/Documents/Dissertation/2d model/honeycomb/alhoneycom3d.fem
'CQUAD4 16667 0 39 21725 228 40'
*** ERROR # 1000 *** in the input data:
Incorrect data in field # 3.
****************
Too many error messages. Aborting run.
Current limit is 10000. Use 'MSGLMT' control card to change this value.
Neel
0 -
Hi Neelc14,
Same file runs for me without any errors.
Can you try this .hm file?
0 -
Hi, when i try to open the file it says that this file is a 17.01-0 file is not backwardly compatible and nothing comes up. I have the student version v14.0 of Hyperworks is there some way you could change the version so that I can view it?
Thanks, Neel
<?xml version="1.0" encoding="UTF-8"?>
0 -
Try this file. Saved from 14.0.
Also, update the Dof on one side of the model. Y is free which deforms the part to a larger extent.
0 -
What should I update it to? Because in a three point bending machine there is a roller support at one end meaning that the dof2 is free and cannot be constrained?
0 -
Neel,
The model is not constrained in the direction of load. Check this and update accordingly
/emoticons/default_smile.png' srcset='/emoticons/smile@2x.png 2x' title=':)' width='20'>
0 -
Hi Prakash,
Sorry one more question i want to change the mesh element size after the model has been created from 3mm to 5mm how would I do that? Because when i do 2d>automesh and select the model and change the size from there an error comes up? What is the easiest way to do this?
Thanks, Neel0 -
Neel,
Can you post the error message, please?
To Remesh Shell elements, what you are following is correct. Also try to disconnect nodes between components before you remesh.
0 -
Hi,
Messages for the job:
*** See next message about line 64 from file:
C:/Users/neel_/OneDrive/Documents/Dissertation/2d model/2dmodel.fem
'SET 1 ELEM LIST'
*** ERROR # 1728 *** in the input data:
Incorrect SET definition.I receive this message. How would I be able to disconnect nodes between components?
Neel
0 -
Neel,
Looks like you have a set with elements, you remeshed those elements and the set has old element IDs.
You need to create another element set.
In order to detach elements, go to 2D page>> Detach is the option
0 -
Hey sorry,
But i receive very large values when I run the optistruct analysis? I dont understand what the problem is, the picture below helps to show the displacement.
Thanks, Neel
<?xml version="1.0" encoding="UTF-8"?>
0 -
The values I should obtain should be much smaller than this around 5mm or so.
0 -
Hi neelc14,
Check the constraints. I think you have an unconstrained model.
Best regards,
Gonçalo
0 -
Altair Employee
