ERROR ON MESH

uri · December 2020

INSPIRE CAST 2020.1.1

Mesh fails, could not find the reason.

Selected Mesh average size = 8 mm

Link for run directory files: https://we.tl/t-G9SSjlAbzu

Please advise

SouravDas0306 · December 2020

Hi Uri,

kindly let me know what type error are you getting or if you can share a snapshot.

Regards,

Sourav

SouravDas0306 · December 2020

Hi Uri,

I would recommend you to use a higher element size, for such a big size component. or you can use Run virtual mold.

Regards

Sourav

SouravDas0306 · December 2020

Hi Uri,

I was able to run the virtual mold.

uri · December 2020

Got an error message while running Virtual mold.

1. Link to the last file version https://we.tl/t-QV227Di0LU

Please advise.
please send me the icust file that you managed to run.

SouravDas0306 · December 2020

Uri Inbar said:

Got an error message while running Virtual mold.

1. Link to the last file version https://we.tl/t-QV227Di0LU

Please advise.

please send me the icust file that you managed to run.

Hi Uri,

In the run dialog, there is an advance tab and in that, there is a mesh component factor, reduce the riser factor. This may solve your problem.

Also PFA file in the link: https://wetransfer.com/downloads/5cfbf54f19cb3395da4c27aa1614662e20201202131401/07feb1

Regards

Sourav

uri · December 2020

Hello

I got the same error (try decreasing the minimum thickness) with the file you managed to run.

1. Please keep in mind that your version is higher then mine. (Mine is 2020.1.1)

2. What were the mesh parameters that you used?

3. Please advise, (Foundry is waiting...)

uri · December 2020

Hello

I decreased the risers mesh factor to 0.6 (Using virtual mold file: https://we.tl/t-QV227Di0LU)

Got the same error message (try decreasing the minimum thickness part 191)

Please advise.

uri · December 2020

Reduced the average mesh size from 8 mm to 6 mm. (Virtual mold)

Now getting the message below without additional details

Please advise.

Link for the Run Folder: https://we.tl/t-XmvozXhfJh

uri · December 2020

CLEAN FILE casting only, no fill, chills risers etc

Link: https://we.tl/t-rwsqSGOxqW

Getting the same error.

Please advise

SouravDas0306 · December 2020

Hi Uri,

PFA link:

https://wetransfer.com/downloads/5cfbf54f19cb3395da4c27aa1614662e20201202131401/b60e0b7f413efbfbb77201a32528d00320201202131401/f57afb

uri · December 2020

Hello Sourav

Thanks for responses.

1. Did you use Virtual mold?

2. What mesh parameters did you use?

Most of my simulations were with average thickness 8 mm and all failed.

Now I am running the simulation, (all items included) with element size 8 mm. Mesh is O.K

Thanks again.

Uri.

SouravDas0306 · December 2020

Uri Inbar said:
Hello Sourav

Thanks for responses.

1. Did you use Virtual mold?

2. What mesh parameters did you use?

Most of my simulations were with average thickness 8 mm and all failed.

Now I am running the simulation, (all items included) with element size 8 mm. Mesh is O.K

Thanks again.

Uri.

Hi Uri,

1. Yes Virtual mold with 8mm mesh size.

I also did one simulation with mesh parameter 6 mm without Virtual mold, which I have sent you via WeTransfer (https://we.tl/t-Y4VyaO7qDu).

Sourav

uri · December 2020

Hello

What is the accuracy difference in results between mold and virtual mold?

ERROR ON MESH

Answers

Categories