ERROR # 1908 Case Control data LOAD=1 is not referenced by any bulk data

Altair Forum User
Altair Forum User
Altair Employee
edited October 2020 in Community Q&A

Dear Prakash,

 

I am trying to do Pressfit simulation in Optistruct with NLSTAT having Dummy Load, SPC & NLPARM 

 

I am getting following error :

 

*** ERROR # 1908 ***
 Case Control data LOAD=1 is not referenced by any bulk data
 relevant for used subcase type.

 

LOAD = 1 which is dummy load collector is referenced in Load step, then also getting this error.

 

Please address how to fix this issue.

 

Thanks & Regards,

Suraj

Tagged:

Answers

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited October 2016

    Hi Suraj,

     

    Can you share the model file?

     

    Please use the FTP lnk to share the file: https://ftam1.altair.com/filedrop/~Ce4god

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited May 28

     

    Dear Prakash,

     

    I have the same error. Could you help me?

     

    I need to build a 2D plate structure, which is subject to flux input to the top middle edge and fixed temperature at bottom two corners.  Optimization is to Minimize TCOMP, with constraint volfrac <= 0.3 .

     I am also not sure whether my model is correct. :( Could you check my file and see whether the flux input and fixed temperature input are correct ? 

     

    Please find my model file as attached, thanks very much.

    problem to be solved.png

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    Hi @wumindao


    Looks like you have a load collector which is not referenced in any load case.

     

    Can you update and check if you are through?

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    Dear Prakash,

     

    I have two load collectors (heat_flux , spc_heat), and they are referenced by load case heat_transfer.

    Please see following screen shot.

     snipaste_20170421_121753.png.5f7f2e1e2052370d9c7f964c3417f608.png

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    @wumindao

     

    Can you share the model file,please?

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited May 28

     

    I share already... Anyway, attached again.     Thanks.

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    Hi,

     

    I am not sure what you are trying to optimize. I see only one response which is volume fraction referenced in both objective and constraint which is not practical.

     

    If you are idea to control thermal compliance create another response for Thermal compliance and use it as objective or constraint. 

     

    2) There is no thickness for non design property

     

    3) I think load collector heat flux is empty no heat flux is seen in your model. 

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited May 28

     

    Dear Prakash,

     

    I am sorry for attached a wrong file, please find attached new updated file. 

    my objective is to Minimize TCOMP (Thermal Compliance)

     

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    For your 3) point.

    3) I think load collector heat flux is empty no heat flux is seen in your model. 

     

    I have add the heat flux on the top middle nodes, but after I export to solver deck, the heat flux missed. 

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    @wumindao

     

    There is no heat flux applied in your new model. Create CHBDYE and apply heat flux (QBDY) on our model.

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited May 28

     

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    Dear Prakash,

     

    Thanks for your file. 

    The reason for this type of error is the heat flux not be applied correctly in my model. 

     

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited April 2017

    @wumindao

     

    No Problem :)/emoticons/default_smile.png' srcset='/emoticons/smile@2x.png 2x' title=':)' width='20'> 

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited December 2017

    please check your loadcase.. there might be no load assign.

  • Altair Forum User
    Altair Forum User
    Altair Employee
    edited January 2020

     *** ERROR # 1908 ***
     Case Control data LOAD=101 is not referenced by any bulk data
     relevant for used subcase type

     

    how to resolve dis?

Categories